Read Sharp MX-LC13 (serv.man27) Technical Bulletin online
MX-7500N MX-LC13 (LARGE CAPACITY TRAYS) 9 – 18
(2) Mechanical Adjustment2
When shifted over +/-2mm less than +/-3mm.
1) Pull out the cassette.
1) Pull out the cassette.
Press the lock button on the front cabinet and lower the paper
feed base tray to the paper supply position. Pull out the tray.
* In case the machine is turned off, If it is necessary to release
the lock manually, push the shaft at the bottom of the front cab-
inet and lower the paper feed base tray to the paper supply
position and pull out the tray.
feed base tray to the paper supply position. Pull out the tray.
* In case the machine is turned off, If it is necessary to release
the lock manually, push the shaft at the bottom of the front cab-
inet and lower the paper feed base tray to the paper supply
position and pull out the tray.
When shifting the line of printing from the center of the paper in
the direction A of arrow as shown below:
the direction A of arrow as shown below:
2) Loosen the blue screws of the rear regulation plate, and move
the plate with referring the carved marks by the dimension
shifted in the direction A (R side), and tighten the blue screws.
shifted in the direction A (R side), and tighten the blue screws.
3) Set a sheet of paper on the paper feed base tray and loosen
the blue screws of the front regulation plate.
Move the front regulation plate to the direction A (R side)?with
pushing paper to the front regulation plate.
Move the front regulation plate to the direction A (R side)?with
pushing paper to the front regulation plate.
4)
Set the front regulation plate to make gap between the rear
regulation plate and paperand tighten the blue screws of the
fron regulation plate.
regulation plate and paperand tighten the blue screws of the
fron regulation plate.
NOTE: Avoid bending paper with too much closing the regulation
plates.
NOTE: When shifting the line of printing from the center of the
paper to rear side, move the front regulation plate to adjust
it.
it.
H. Diagonal feed adjustment
(1) Diagonal Adjustment
1)
Pull out the cassette.
Press the lock button on the front cabinet and lower the paper
feed base tray to the paper supply position. Pull out the tray.
* In case the machine is turned off, If it is necessary to release
the lock manually, push the shaft at the bottom of the front cab-
inet and lower the paper feed base tray to the paper supply
position and pull out the tray.
Press the lock button on the front cabinet and lower the paper
feed base tray to the paper supply position. Pull out the tray.
* In case the machine is turned off, If it is necessary to release
the lock manually, push the shaft at the bottom of the front cab-
inet and lower the paper feed base tray to the paper supply
position and pull out the tray.
2)
Adjust the diagonal feed.
3)
Set a sheet of paper on the paper feed base tray and adjust
the width of the regulation plate.
In the case of diagonal feed 1
Loosen the 2 blue screw (1) on the front regulation plate.
Referring to the degree of diagonal feed, move the regulation
plate in the clockwize direction and fix the blue screw.
the width of the regulation plate.
In the case of diagonal feed 1
Loosen the 2 blue screw (1) on the front regulation plate.
Referring to the degree of diagonal feed, move the regulation
plate in the clockwize direction and fix the blue screw.
5HDU
%OXH6FUHZV
5HJXODWLRQ3ODWH
)URQW
3DSHU
3XVKSDSHUWRWKHIURQW
UHJXODWLRQSODWH
UHJXODWLRQSODWH
MM
3DSHU
Diagonal feed 1
Diagonal feed 2
Transport
direction
direction
)URQW
3DSHU
TopPage
2
: ‘14/Jan
2
Click on the first or last page to see other MX-LC13 (serv.man27) service manuals if exist.