Read Sharp MX-LC13 (serv.man15) Technical Bulletin online
MX-7500N MX-LC13 (LARGE CAPACITY TRAYS) 9 – 11
3) Adjust the LCT position to push or pull with holding the pillar of
LCT as the figure below.
In case the print image shifts to front: Push LCT to rear
direction.
In case the print image shifts to rear: Pull LCT to front direc-
tion.
After finish the adjustment, fix the unit with the 2 blue screws.
In case the print image shifts to front: Push LCT to rear
direction.
In case the print image shifts to rear: Pull LCT to front direc-
tion.
After finish the adjustment, fix the unit with the 2 blue screws.
If these adjustment above couldn’t adjust Off-center completely, the
following adjustment is needed.
When shifting the line of printing from the center of the paper in the
direction A of arrow as shown below:
1) Separate the LCT from MX-RB14.
following adjustment is needed.
When shifting the line of printing from the center of the paper in the
direction A of arrow as shown below:
1) Separate the LCT from MX-RB14.
When separating, tighten the screw to release the lock.
When connecting again, loosen the screw after connection.
When connecting again, loosen the screw after connection.
2) Open the left side door and open the LCT delivery paper guide
unit.
3) Loosen the 2 blue screws.
4) Shift the connection unit to the following direction and fix the 2
4) Shift the connection unit to the following direction and fix the 2
blue screws.
In case the print image shifts to front;
- Shift the Connection plate unit to the front.
In case the print image shifts to rear: Use F hole.
- Shift the Connection plate unit to the rear.
- Shift the Connection plate unit to the front.
In case the print image shifts to rear: Use F hole.
- Shift the Connection plate unit to the rear.
5)
To stick the L-shape driver (Packed items No.12) to the adjust-
ment hole, the connection plate unit position can be adjusted
to the following 4 steps.
F1.5 / 3 : Shift the unit 3 / 1.5 mm to front.
R1.5 / 3 : Shift the unit 3 / 1.5 mm to rear.
ment hole, the connection plate unit position can be adjusted
to the following 4 steps.
F1.5 / 3 : Shift the unit 3 / 1.5 mm to front.
R1.5 / 3 : Shift the unit 3 / 1.5 mm to rear.
6)
Reinstall LCT to MX-RB14.
Use the mark of the rear regulation plate, and fix the blue
screw at the position so that the clearance between paper and
the rear regulation plate is evenly 1mm.
NOTE: Fasten the screw which was unfastened in the proceu-
dre 1).
Use the mark of the rear regulation plate, and fix the blue
screw at the position so that the clearance between paper and
the rear regulation plate is evenly 1mm.
NOTE: Fasten the screw which was unfastened in the proceu-
dre 1).
(2) Mechanical Adjustment2
When shifted over +/-2mm less than +/-3mm.
1)
1)
Pull out the cassette.
Press the lock button on the front cabinet and lower the paper
feed base tray to the paper supply position. Pull out the tray.
* In case the machine is turned off, If it is necessary to release
the lock manually, push the shaft at the bottom of the front cab-
inet and lower the paper feed base tray to the paper supply
position and pull out the tray.
Press the lock button on the front cabinet and lower the paper
feed base tray to the paper supply position. Pull out the tray.
* In case the machine is turned off, If it is necessary to release
the lock manually, push the shaft at the bottom of the front cab-
inet and lower the paper feed base tray to the paper supply
position and pull out the tray.
When shifting the line of printing from the center of the paper in
the direction A of arrow as shown below:
the direction A of arrow as shown below:
&RQQHFWLRQSODWHXQLW
5
)
5
)
Click on the first or last page to see other MX-LC13 (serv.man15) service manuals if exist.