MX-FX10 (serv.man3). MX-FX10 Fax Operation Manual - Sharp Copying Equipment User Guide / Operation Manual. Page 99

Read Sharp MX-FX10 (serv.man3) User Guide / Operation Manual online

97
SYSTEM SETTINGS
8
OWN PASSCODE SET
Use this setting to program the fax number of the 
machine and the name of the user. The programmed 
name and number are printed at the top of each fax 
page you send. The number is also used as a 
passcode when performing polling reception "USING 
THE POLLING FUNCTION" (page 37).
You can check your programmed name and number 
by printing out the "SYSTEM SET LIST". (Page 95)
• A maximum of 20 digits can be stored for the fax 
number.
• A maximum of 18 letters can be stored for the name.
1
Follow steps 1 through 6 of "INITIAL 
PROCEDURE" (page 94).
2
Select "INITIAL SETTING" with the [
] or 
[
] key and then press the [OK] key.
3
Select "OWN PASSCODE SET" with the 
[
] or [
] key and then press the [OK] 
key.
4
Select "STORE" with the [
] or [
] key 
and then press the [OK] key.
5
Enter your fax number with the numeric 
keys and then press the [OK] key.
• If you make a mistake, press the [C] key and re-enter 
the number.
• To enter "+", press the 
 key.
6
Enter your name and then press the 
[START] key (
).
See "ENTERING CHARACTERS" (page 82) for the 
procedure for entering letters.
SPEAKER VOLUME
This setting is used to adjust the on-hook volume, the 
ringing volume, the line monitor volume, the TX/RX 
end sound volume, the original scanning end sound 
volume, and the tone output volume. All volume 
settings are initially set to "MIDDLE".
1
Follow steps 1 through 6 of "INITIAL 
PROCEDURE" (page 94).
2
Select "INITIAL SETTING" with the [
] or 
[
] key and then press the [OK] key.
3
Select "SPEAKER VOLUME" with the [
] 
or [
] key and then press the [OK] key.
4
Select name of the volume that you wish 
to adjust with the [
] or [
] key and then 
press the [OK] key.
5
Select the desired volume level with the 
[
] or [
] key and then press the [OK] key.
• "HIGH", "MIDDLE" or "LOW" can be selected for the 
on hook volume.
• "HIGH", "MIDDLE", "LOW" or "OFF" can be selected 
for volumes other than the on hook volume.
TX/RX END SOUND
This setting is used to select the beep pattern that 
signals the end of transmission or reception. "PATTERN 
1", "PATTERN 2" or "PATTERN 3" can be selected.
1
Follow steps 1 through 6 of "INITIAL 
PROCEDURE" (page 94).
2
Select "INITIAL SETTING" with the [
] or 
[
] key and then press the [OK] key.
3
Select "TX/RX END SOUND" with the [
] 
or [
] key and then press the [OK] key.
4
Select "SEND" or "RECEIVE" with the [
] 
or [
] key and then press the [OK] key.
5
Select "PATTERN 1", "PATTERN 2", or 
"PATTERN 3" with the [
] or [
] key and 
then press the [OK] key.
Before pressing the [OK] key to store your selection, 
you can press the 
 key to listen to the selected 
pattern.
TX/RX END SOUND LENGTH
This setting is used to select the length of the end sound 
in seconds. Selections are "2.0 sec", "2.5 sec", "3.0 sec", 
"3.5 sec", and "4.0 sec". "3.0 sec" is normally selected.
1
Follow steps 1 through 6 of "INITIAL 
PROCEDURE" (page 94).
2
Select "INITIAL SETTING" with the [
] or 
[
] key and then press the [OK] key.
3
Select "TX/RX END SOUND LENGTH" with 
the [
] or [
] key and then press the [OK] 
key.
4
Select the number of seconds with the [
] 
or [
] key and then press the [OK] key.
To clear the programmed fax number and 
name, follow these steps:
(1) Select "DELETE" in step 4 and then 
press the [OK] key.
(2) Select "DELETE" with the [
] or [
] 
key and then press the [OK] key.
Note
Pegasus-E_Fax_Ex.book  97 ページ  ２００９年６月５日　金曜日　午後１時４９分
Display
Click on the first or last page to see other MX-FX10 (serv.man3) service manuals if exist.
Random: