Read Sharp MX-FNX6 Service Manual online
MX-FNX6 MECHANISM 3 – 5
7)
The first set is discharged.
8)
The first sheet, the second sheet, and the third sheet of the
second set are discharged together to the staple tray.
second set are discharged together to the staple tray.
6. Rise-fall mechanism
<Tray assembly>
The Tray assembly rises or falls depending on the copy paper
quantity (paper stack height) discharged on the tray. The height is
always adjusted by the OFF state of the paper surface sensor.
• When discharging in the shift mode:
The Tray assembly rises or falls depending on the copy paper
quantity (paper stack height) discharged on the tray. The height is
always adjusted by the OFF state of the paper surface sensor.
• When discharging in the shift mode:
Paper surface sensor on the end fence side
• When discharging in the staple mode:
Paper surface sensor on the filler
1)
Falling operation
When the discharged copy paper is loaded on the tray and the
filler is lifted to turn on the paper surface detection sensor
lower for 3 sec or more, the lift motor rotates to fall the shift
tray. The falling operation varies depends on the mode.
When the discharged copy paper is loaded on the tray and the
filler is lifted to turn on the paper surface detection sensor
lower for 3 sec or more, the lift motor rotates to fall the shift
tray. The falling operation varies depends on the mode.
Staple:
The lift motor rotates for a certain time to lower the tray height
for a certain interval, adjusting the height.
The lift motor rotates for a certain time to lower the tray height
for a certain interval, adjusting the height.
Shift:
The shift tray lifts up to the position where the paper surface
sensor is turned on. Then, the tray falls to turn off the paper
surface sensor, adjusting the height.
The shift tray full detection is made when the sensor is turned
on and it is displayed on the operation panel, and copying is
stopped. Cancel is made by removing copy paper.
The shift tray lifts up to the position where the paper surface
sensor is turned on. Then, the tray falls to turn off the paper
surface sensor, adjusting the height.
The shift tray full detection is made when the sensor is turned
on and it is displayed on the operation panel, and copying is
stopped. Cancel is made by removing copy paper.
2)
Rising operation
When copy paper is removed from the shift tray and the paper
surface sensor upper is turned on, the shift tray rises. It stops
when the sensor is turned off.
When copy paper is removed from the shift tray and the paper
surface sensor upper is turned on, the shift tray rises. It stops
when the sensor is turned off.
7. Staple jogger mechanism
A. Stack mechanism
Copy paper branched to the staple tray is transported to the staple
tray. After the staple paper exit sensor turns off (A4Y), the align-
ment roller SOL turns on for a certain time (varying depending on
the size and the quantity). The alignment roller pushes paper to the
tray stopper to align the rear edges of paper.
tray. After the staple paper exit sensor turns off (A4Y), the align-
ment roller SOL turns on for a certain time (varying depending on
the size and the quantity). The alignment roller pushes paper to the
tray stopper to align the rear edges of paper.
B. Jogger mechanism
Copy paper rear edges are aligned by stack operation of (A), then
copy paper side edges are aligned by jogger operation.
First, the jogger fence closes to 7mm open from the right and the
left edges of paper by the ON signal (copy start).
When the lead edge of the transported paper passes the staple
paper exit sensor, the jogger fence closes 5mm to receive paper
and performs the operation of (A) to align the rear edges.
Then, the jogger fence closes 2.6mm furthermore to align the side
edges.
When the jogger operation is completed, the jogger fence opens
again to 7mm open from the paper edges and the machine enters
the standby state of the next paper.
copy paper side edges are aligned by jogger operation.
First, the jogger fence closes to 7mm open from the right and the
left edges of paper by the ON signal (copy start).
When the lead edge of the transported paper passes the staple
paper exit sensor, the jogger fence closes 5mm to receive paper
and performs the operation of (A) to align the rear edges.
Then, the jogger fence closes 2.6mm furthermore to align the side
edges.
When the jogger operation is completed, the jogger fence opens
again to 7mm open from the paper edges and the machine enters
the standby state of the next paper.
Lift motor
Shift tray lower
limit sensor
limit sensor
Filler paper surface sensor
Paper surface
sensor on the end
fence side
sensor on the end
fence side
Jogger fence
Sliding roller
Jogger motor
Jogger HP
sensor
sensor
Click on the first or last page to see other MX-FNX6 service manuals if exist.