Read Sharp MX-B201D (serv.man9) Service Manual online
MX-B201/B201D USER PROGRAM 12 - 3
:'11/Oct/17
1
Print mode
*1: The scanning speed increases when the USB 2.0 mode is set to "HI-SPEED", however, the printing speed does not increase considerably.
*2: When the 250-sheet paper feed unit is installed.
*3: When the Network expansion kit is installed.
Fax mode
Program
number
Program name
Setting codes
(factory default setting
appears in bold)
Explanation
1
FORCED OUTPUT
1: ON
2: OFF
2: OFF
When this function is enabled, printing in printer mode will automatically
continue using a different size of paper if the specified size of paper runs out
in all trays. This feature does not function in copy mode.
continue using a different size of paper if the specified size of paper runs out
in all trays. This feature does not function in copy mode.
2
USB 2.0 MODE
SWITCH *1
SWITCH *1
1: FULL-SPEED
2: HI-SPEED
2: HI-SPEED
This sets the USB 2.0 data transfer speed. To obtain the fastest speed when
using the USB 2.0 connector, first verify that your computer meets the
system requirements (operating system and driver), and then use this
program to change the USB 2.0 mode to "Hi-Speed". Note that the setting
should not be changed while running a TWAIN driver.
using the USB 2.0 connector, first verify that your computer meets the
system requirements (operating system and driver), and then use this
program to change the USB 2.0 mode to "Hi-Speed". Note that the setting
should not be changed while running a TWAIN driver.
3
AUTO TRAY SWITCH*2
1: ON
2: OFF
2: OFF
This is selectable when the optional paper tray is installed.
(This is not shown when the optional tray is not installed.)
(This is not shown when the optional tray is not installed.)
4
ENABLE TCP/IP *3
1: ON
2: OFF
2: OFF
This is to select whether or not to make the network connection by TCP/IP
protocol effective.
protocol effective.
5
ENABLE DHCP *3
1: ON
2: OFF
2: OFF
This is to select whether or not to apply to DHCP network connection.
6
IP ADDRESS SETTING
*3
*3
1: IP ADDRESS
2: SUBNETMASK
3: DEFAULT GATEWAY
2: SUBNETMASK
3: DEFAULT GATEWAY
This is to set IP address, Subnetmask and Default Gateway from the
machine. This can also be used to check the machine’s IP ADDRESS when
"IP ADDRESS" is selected. When the program number 4 "ENABLE DHCP"
is "ON" and the machine is under DHCP environment, the IP address on the
display is shown with "
machine. This can also be used to check the machine’s IP ADDRESS when
"IP ADDRESS" is selected. When the program number 4 "ENABLE DHCP"
is "ON" and the machine is under DHCP environment, the IP address on the
display is shown with "
" at the tail end.
Program
number
Program name
Setting codes
(factory default setting
appears in bold)
Explanation
1
DOC. GLASS SIZE
1: 8.5x11
2: 8.5x14
3: A4
2: 8.5x14
3: A4
• Set the size of an original faxed from the document glass.
2
FIXED DOC. SIZE
1: 8.5x11
2: 8.5x14
3: A4
2: 8.5x14
3: A4
• Set the default size of originals faxed from the document glass.
3
RESO. PRIORITY
1: STANDARD
2: FINE
3: SUPER FINE
2: FINE
3: SUPER FINE
• Set the default resolution for fax transmission.
4
# OF RINGS (AUTO)
0 - 9 (2)
• Set the number of rings on which the machine answers calls in automatic
reception mode.
5
# OF RINGS (MANUAL)
0 - 9 (0)
• Set the number of rings on which the machine answers calls in manual
reception mode.
6
AUTO LISTING
1: ON
2: OFF
2: OFF
• Enable automatic printing of the Activity Report when information on a
total of 50 fax transmissions/receptions accumulates.
7
PRINT SELECTION
(1) TRANSMISSION
1: ALWAYS PRINTS
2: ERROR ONLY
3: NEVER PRINTS
1: ALWAYS PRINTS
2: ERROR ONLY
3: NEVER PRINTS
• Select the condition for printing reports on fax transmissions.
(2) BROADCAST
1: ALWAYS PRINTS
2: ERROR ONLY
3: NEVER PRINTS
1: ALWAYS PRINTS
2: ERROR ONLY
3: NEVER PRINTS
• Select the condition for printing reports on broadcast transmissions.
(3) RECEPTION
1: ALWAYS PRINTS
2: ERROR ONLY
3: NEVER PRINTS
1: ALWAYS PRINTS
2: ERROR ONLY
3: NEVER PRINTS
• Select the condition for printing reports on received faxes.
(4) IMAGE MEM. PRINT
1: ALWAYS PRINTS
2: ERROR ONLY
3: NEVER PRINTS
1: ALWAYS PRINTS
2: ERROR ONLY
3: NEVER PRINTS
• Enable printing of the original image on transaction reports.
8
RECALL TIMES BUSY
00 - 14 (02)
• Set the number of recall attempts that are made when the line is busy.
9
RECALL TIMES ERR
0 - 1 (1)
• Set the number of recall attempts that are made when a communication
error occurs.
10
RECALL INT. BUSY
01 - 15 min. (03 min.)
• Set the interval between recall attempts when the line is busy. 1 to 15 min-
utes can be selected.
1
1
1
Click on the first or last page to see other MX-B201D (serv.man9) service manuals if exist.