Read Sharp MX-5500N / MX-6200N / MX-7000N (serv.man25) Peripheral online
3
Precautions
Precautions
Always observe the following general precautions when servicing the Fiery X3eTY2:
1.
Report any shipping damage.
If there is any evidence of shipping or handling damage to packing boxes or their
contents, save the damaged boxes and parts, call the shipper immediately to file a claim,
and notify your authorized service/support center.
contents, save the damaged boxes and parts, call the shipper immediately to file a claim,
and notify your authorized service/support center.
2.
Never alter an existing network without permission.
The Fiery X3eTY2 is probably connected to an existing Local Area Network (LAN)
based on Ethernet hardware. The network is the link between the customer’s computer,
existing laser printers, and other prepress equipment. Never disturb the LAN by breaking
or making a network connection, altering termination, installing or removing
networking hardware or software, or shutting down networked devices without the
knowledge and express permission of the network administrator.
based on Ethernet hardware. The network is the link between the customer’s computer,
existing laser printers, and other prepress equipment. Never disturb the LAN by breaking
or making a network connection, altering termination, installing or removing
networking hardware or software, or shutting down networked devices without the
knowledge and express permission of the network administrator.
3.
Never assign an IP address in Network Setup.
Only the network administrator should assign an IP address on a network device.
Entering an incorrect IP address to the Fiery X3eTY2 can cause unpredictable errors on
any or all devices.
Entering an incorrect IP address to the Fiery X3eTY2 can cause unpredictable errors on
any or all devices.
4.
Follow standard ESD (electrostatic discharge) precautions while working on the internal
components of the Fiery X3eTY2.
components of the Fiery X3eTY2.
Static electricity is always a concern when servicing electronic devices. It is highly
unlikely that the area around the Fiery X3eTY2 is static-free. Carpeting, leather-soled
shoes, synthetic clothing fibers, silks, and plastics may generate a static charge of more
than 10,000 volts. Static discharge is capable of destroying the circuits etched in silicon
microchips, or dramatically shortening their life span. By observing standard precautions,
you can avoid extra service calls and save the cost of a new board.
unlikely that the area around the Fiery X3eTY2 is static-free. Carpeting, leather-soled
shoes, synthetic clothing fibers, silks, and plastics may generate a static charge of more
than 10,000 volts. Static discharge is capable of destroying the circuits etched in silicon
microchips, or dramatically shortening their life span. By observing standard precautions,
you can avoid extra service calls and save the cost of a new board.
When possible, work on a ground-connected antistatic mat. Wear an antistatic
wristband, grounded at the same place as the antistatic mat. If that is not possible:
wristband, grounded at the same place as the antistatic mat. If that is not possible:
• Attach a grounding strap to your wrist. Attach the other end to a good ground.
• After removing an electronic component, place it into an antistatic bag immediately.
Do not walk across a carpet or vinyl floor while carrying an unprotected board.
• Leave new electronic components inside their antistatic bags until you are ready to
install them.
• When you unpack the electronic components, touch a metal area of the Fiery X3eTY2
to discharge the static on your body. Place the components on a grounded antistatic
surface, component-side up.
surface, component-side up.
5.
Avoid flexing a printed circuit board, and handle it by opposing edges (not corners) only.
6.
Never set a cup of coffee—or any liquid—on or near any components or the MFP.
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man25) service manuals if exist.