Read Sharp MX-2630 Service Manual online
MX-2630N 2 – 8
SKEW: Judgment of the LSU skew adjustment result. OK or NG.
PHASE: OPC drum phase adjustment value of the previous time
5)
The procedures 2) to 4) again, and check to confirm that C, M,
and Y (SKEW) are OK.
and Y (SKEW) are OK.
If any of them is NG, turn the LSU skew adjustment screw of the
corresponding color to adjust.
corresponding color to adjust.
When the adjustment is made by turning the LSU skew adjustment
screw of K, the states of C, M and Y (SKEW) are changed. Execute
SIM50-22 to check to confirm that C, M, and Y (SKEW) are OK.
screw of K, the states of C, M and Y (SKEW) are changed. Execute
SIM50-22 to check to confirm that C, M, and Y (SKEW) are OK.
When an abnormality occurs, "ERROR" is displayed.
In this case, check each drive section and the process section.
(2)
Copy color balance and density check
Method
Make a copy of the gray test chart (UKOG-0162FCZZ) and a copy of
the servicing color test chart (UKOG-0326FCZZ/UKOG-0326FC11),
and check that they are proper.
the servicing color test chart (UKOG-0326FCZZ/UKOG-0326FC11),
and check that they are proper.
a. Note for execution of the color balance and density check in the
color copy mode
color copy mode
To check the copy color balance and density, use the gray test chart
(UKOG-0162FCZZ) and the servicing color test chart (UKOG-
0326FCZZ/UKOG-0326FC11). Set the copy density level to "3" in
the Text/Printed Photo mode (Manual), and make a copy.
(UKOG-0162FCZZ) and the servicing color test chart (UKOG-
0326FCZZ/UKOG-0326FC11). Set the copy density level to "3" in
the Text/Printed Photo mode (Manual), and make a copy.
At that time, all the color balance adjustments in the user adjustment
mode must be set to the default (center).
mode must be set to the default (center).
In addition, be sure to use the specified paper for color.
b. Note for checking the monochrome copy mode density
To check the density, use the gray test chart (UKOG-0162FCZZ).
Set the copy density level to "Manual 3" in the Text/Printed Photo
mode (Manual).
Set the copy density level to "Manual 3" in the Text/Printed Photo
mode (Manual).
In addition, all the color balance adjustments in the user adjustment
mode must be set to the default (center).
mode must be set to the default (center).
[Check with the gray test chart (UKOG-0162FCZZ)]
In the copy density check with the gray test chart, check to insure the
following conditions.
following conditions.
For the color (gray) balance, use the servicing color test chart (UKOG-
0326FCZZ/UKOG-0326FC11) to check.
0326FCZZ/UKOG-0326FC11) to check.
[Check with the servicing color test chart (UKOG-0326FCZZ/UKOG-
0326FC11)]
0326FC11)]
In the copy color balance check with the servicing color test chart,
check to insure the following conditions.
check to insure the following conditions.
1
2
3
4
5
6
7
8
9
10
W
SHARP GRAY CHART
SHARP gray chart
Patch 1 is
slightly copied.
slightly copied.
Patch 2 is copied.
(Color copy)
1
2
3
4
5
6
7
8
9
10
W
SHARP GRAY CHART
SHARP gray chart
Patch 1 is not copied.
Patch 2 is
slightly copied.
slightly copied.
Patch 3 is copied.
(Black-and-white copy)
Serviceman chart (Color patch section)
The densities of patches 1 - 6 of
each color are properly balanced.
each color are properly balanced.
Patch 7 is slightly
copied or not copied.
copied or not copied.
(Color copy)
Click on the first or last page to see other MX-2630 service manuals if exist.