Read Sharp MX-2630 Service Manual online
MX-2630N 2 – 7
3)
Adjust the guide plates A and B by squeezing their lock levers and
D. Specifications setup
Use simulation 26-6 to set the machines destination.
After completion of destination settings, change the set values to cus-
tomize the following settings.
tomize the following settings.
3. Image quality check
A. Execution items
Execute the following items.
When there are defects in a picture by the contents mentioned above,
you carry out the following contents, and confirm a picture.
you carry out the following contents, and confirm a picture.
B. Description
(1)
Print engine image distortion adjustment (Manual
adjustment) / OPC drum phase adjustment
(Automatic adjustment) / Color registration
adjustment (Automatic adjustment)
adjustment) / OPC drum phase adjustment
(Automatic adjustment) / Color registration
adjustment (Automatic adjustment)
This adjustment performs the print engine image distortion adjustment,
the OPC drum phase adjustment, and the color registration adjust-
ment simultaneously.
the OPC drum phase adjustment, and the color registration adjust-
ment simultaneously.
1)
Enter SIM50-22 mode.
2)
Press [EXECUTE] key.
[EXECUTE] key is highlighted and the image registration auto-
matic adjustment is started. (It takes about 30 sec to complete the
adjustment.)
matic adjustment is started. (It takes about 30 sec to complete the
adjustment.)
3)
When the adjustment is completed, [EXECUTE] key returns to the
normal display, and the value of the adjustment result is dis-
played.
normal display, and the value of the adjustment result is dis-
played.
The current skew level for each color is displayed on the SKEW
display section.
display section.
4)
Write down the displayed skew level.
(Meaning of the skew level value and the adjustment procedure)
(Meaning of the skew level value and the adjustment procedure)
* If "OK" is displayed for all items of SKEW C,
M, and Y, there is no need to perform the adjustment.
* When "R" is displayed at the head of the value, turn the LSU
skew adjustment screw clockwise.
* When "L" is displayed at the head of the value, turn the LSU
skew adjustment screw counterclockwise.
* The turning amount of the adjustment screw corresponds to
each adjustment value. C, M, and Y indicate numbers of clicks.
The display value is rounded at the decimal point.
* "C, M, and Y(SKEW)" shows the number of adjustment click
steps for each adjustment screw of C, M, and Y.
steps for each adjustment screw of C, M, and Y.
Contents in ( )
MIAN, SUB: Difference from the previous adjustment value of
image registration.
image registration.
Example:
If 105 for this time and 103 for the previous time,
it is displayed as 105.0 (+2.0).
it is displayed as 105.0 (+2.0).
SIM No
Content
26
6
Used to set the destination.
SIM No
Content
26
3
Used to set the auditor specification mode.
5
Used to set the count mode of the total counter and
the maintenance counter.
the maintenance counter.
18
Used to set YES/NO of the toner save mode (Only in
UK and Japan versions)
* For other destination versions, this setup is made
UK and Japan versions)
* For other destination versions, this setup is made
by the user program.
52
Used to set YES/NO of counting when non-print
paper is passed through each counter.
paper is passed through each counter.
65
Used to set the limit number of sheets for stapling.
Ĭ
ĭ
Į
No.
Item
SIM
1
Print engine image distortion adjustment (Manual
adjustment) / OPC drum phase adjustment
(Automatic adjustment) / Color registration adjustment
(Automatic adjustment)
adjustment) / OPC drum phase adjustment
(Automatic adjustment) / Color registration adjustment
(Automatic adjustment)
50-22
2
Copy color balance and density check
3
Printer color balance/density check
64-5
No.
Item
SIM
4
Copy/Printer color balance adjustment (Automatic
adjustment)
adjustment)
46-74
5
Print/scan image off-center, lead edge position
adjustment
adjustment
50-10
Click on the first or last page to see other MX-2630 service manuals if exist.