Read Sharp DM-2000 (serv.man7) Service Manual online
[10] USER SETUP
The user programs allow the parameters of certain functions to be set,
changed, or canceled as desired.
changed, or canceled as desired.
1. List of user programs
This DM System has the following user programs.
Program
No.
Program
name
Description
1
Auto clear
time
time
Sets the auto clear time. The system
returns to the initial settings when the
auto clear time elapses after the last
copy is made.
returns to the initial settings when the
auto clear time elapses after the last
copy is made.
2
Preheat
mode
mode
Sets the time that elapses before the
system enters the preheat mode after
any operation is made.
system enters the preheat mode after
any operation is made.
3
Auto power
shut-off
timer
shut-off
timer
Sets the time that elapses before the
system enters the auto power shut-off
mode after any operation is made.
system enters the auto power shut-off
mode after any operation is made.
4
Stream
feeding
mode*
feeding
mode*
Enables or disables the stream feeding
mode when an optional single pass
feeder (SPF) is installed.
mode when an optional single pass
feeder (SPF) is installed.
5
Auto power
shut-off
setting
shut-off
setting
Enables or disables the auto power
shut-off mode.
shut-off mode.
6
Border line
for 2 in 1
or 4 in 1*
for 2 in 1
or 4 in 1*
Enables or disables the border line
which is printed in 2 in 1 or 4 in 1
copying when an optional electronic
sorting kit and an optional SPF are
installed.
which is printed in 2 in 1 or 4 in 1
copying when an optional electronic
sorting kit and an optional SPF are
installed.
7
Rotation
copy*
copy*
Enables or disables rotation of original
images.
images.
8
Auto paper
select mode
select mode
Enables or disables the auto paper
selection.
selection.
9
Auto tray
switching
switching
Enables or disables the automatic tray
switching which occurs when paper in a
tray runs out. (This switching cannot
switch to the bypass tray.)
switching which occurs when paper in a
tray runs out. (This switching cannot
switch to the bypass tray.)
10
Auditing
mode
mode
Enables or disables the auditing mode,
which controls access to copier.
which controls access to copier.
11
Account
number
entry
number
entry
Registers accounts for auditing mode.
12
Account
number
change
number
change
Changes account numbers for auditing
mode.
mode.
13
Account
number
deletion
number
deletion
Deletes accounts for auditing mode.
14
Number of
copies per
account
copies per
account
Displays the total number of copies
made against account numbers.
made against account numbers.
15
Resetting
account
account
Resets all audit accounts or resets any
desired individual account.
desired individual account.
16
Erase
width
adjustment*
width
adjustment*
Sets the amount of the edge erase and
center erase areas.
center erase areas.
17
Layout in 2
in 1 copy*
in 1 copy*
Selects a pattern for 2 in 1 copying.
18
Layout in 4
in 1 copy*
in 1 copy*
Selects a pattern for 4 in 1 copying.
19
Offset of
paper
output tray
paper
output tray
Enables or disables the offset function
of the paper output tray. The offset
function can be specified respectively
for the upper and lower areas
separated by an optional job separator
tray kit.
of the paper output tray. The offset
function can be specified respectively
for the upper and lower areas
separated by an optional job separator
tray kit.
∗ These programs do not affect the copier functions unless certain op-
tional equipment is installed.
2. Setting the user programs
1) Press and hold the light ( ) key for more than 5 seconds until
all the alarm indicators ( , , , , and ) blink and "-
-" appears in the copy quantity display.
-" appears in the copy quantity display.
2) Enter a program number using the numeric keys.
● The selected program number will blink in the copy quantity dis-
play.
● If a mistake is made in steps 2) to 4), press the CLEAR (clear)
key. The copier will return to step 2).
● The program numbers are shown in the table below.
For example, to change the setting of the auto power shut-off timer,
press key 3.
press key 3.
Program name
Program No.
Auto clear time
1
Preheat mode
2
Auto power shut-off timer
3
Stream feeding mode
4
Auto power shut-off setting
5
Border line for 2 in 1 or 4 in 1
6
Rotation copy
7
Auto paper select mode
8
Auto tray switching
9
Auditing mode
10
∗
Account number entry
11
∗
Account number change
12
∗
Account number deletion
13
∗
Number of copies per account
14
∗
Resetting account
15
∗
Erase width adjustment
16
Layout in 2 in 1 copy
17
Layout in 4 in 1 copy
18
Offset of paper output tray
19
∗ For operation of these programs afterstep 3.
3) Press the START key.
● For programs 1 to 9 and 16 to 19, the entered program number
will be steadily lit on the left side of the copy quantity display
and the currently selected parameter number for the program
will blink on the right side.
and the currently selected parameter number for the program
will blink on the right side.
● For programs 10 to 15 (programs for auditing accounts), the
display varies with the program number.
4) Select the desired parameter using the numeric keys.
● The entered parameter number will blink on the right side of the
copy quantity display.
● The parameters are shown in the table below.
DM-2000
10 – 1
Click on the first or last page to see other DM-2000 (serv.man7) service manuals if exist.