AR-M700 (serv.man28). Self diag message and troubleshooting - Sharp Copying Equipment Service Manual (repair manual). Page 28

Read Sharp AR-M700 (serv.man28) Service Manual online

: Feb. 9 2004
1
AR-M550/M620/M700  SELF DIAG MESSAGE AND TROUBLESHOOTING  9 - 28
Main 
code
Sub 
code
Title
FAX-BOX incompatibility trouble
F6
97
Phenomenon
Display
Lamp
Message
Details
The FAX-BOX PWB is 
not one for the AR-FX8. 
(FAX detection)
If the FAX-BOX modem 
controller PWB 
information (hard 
detection) is not for the 
AR-FX8, it is judged as 
an error.
Section
FAX
Operation 
mode
Note 
Case 1
Trouble 
position/
Cause
Because the FAX-BOX 
modem controller PWB 
information (hard 
detection) is not for the 
AR-FX8. (The modem 
controller PWB for the 
AR-FX5 or the AR-FX6 is 
used.)
Remedy
Check the FAX-BOX 
modem controller PWB.
Replace it with a modem 
controller PWB for the 
AR-FX8.
Note 
Main 
code
Sub 
code
Title
Combination error of the FAX-BOX 
destination information and the 
machine destination information
F6
98
Phenomenon
Display
Lamp
Message
Details
Combination error of the 
FAX-BOX destination 
information and the 
machine destination 
information
When the destination 
information stored in the 
FAX-BOX EEPROM is 
compared with that of the 
machine, and if the 
combination is improper, 
it is judged as an error.
Section
FAX
Operation 
mode
Note 
Case 1
Trouble 
position/
Cause
Because of improper 
combination between the 
destination information 
stored in the EEPROM on 
the FAX-BOX PWB and 
that of the machine (set 
with SIM 26-6).
Remedy
Check the destination of 
the FAX-BOX.
Check the machine 
destination with SIM 26-6.
Use a proper combination 
of the machine and the 
FAX-BOX.
Note 
Main 
code
Sub 
code
Title
FAX board EEPROM read/write 
error
F7
01
Phenomenon
Display
Lamp
Message
Details
FAX board EEPROM 
read/write error
ACK from the EEPROM 
cannot be checked.
Section
FAX
Operation 
mode
Note 
Case 1
Trouble 
position/
Cause
EEPROM trouble
FAX PWB EEPROM 
access circuit trouble
Remedy
Replace the EEPROM.
Re-setup the soft SW.
Note 
Main 
code
Sub 
code
Title
PRT centro port check error
F9
02
Phenomenon
Display
Lamp
Message
Details
PRT centro port check 
error
Section
Controller
Operation 
mode
Note 
Case 1
Trouble 
position/
Cause
Centro port trouble
MFP controll PWB 
trouble
Remedy
Replace the MFP controll 
PWB.
Note 
Main 
code
Sub 
code
Title
Thermistor open/Fusing unit not 
installed
H2
00/
HL1
Phenomenon
Display
Lamp
Message
01/
HL2
Details
Thermistor open (An 
input voltage of 2.95V or 
above is detected.)
Fusing unit not installed
02/
HL3
Section
Engine
Operation 
mode
Note 
Case 1
Trouble 
position/
Cause
Thermistor trouble
Control PWB trouble
Improper connection of 
the fusing section 
connector
AC power trouble
Fusing unit not installed
Remedy
Check the harness and 
the connector between 
the thermistor and the 
control PWB.
Use SIM 14 to clear the 
self diag display.
Note 
1
Page of 38
Display

Click on the first or last page to see other AR-M700 (serv.man28) service manuals if exist.