AR-M700 (serv.man26). Setting and adjustments - Sharp Copying Equipment Service Manual (repair manual). Page 30

Read Sharp AR-M700 (serv.man26) Service Manual online

AR-M550/M620/M700  SETTING AND ADJUSTMENTS  7 - 30
This adjustment is needed in the following situations: 
• The CCD unit has been replaced. 
• U2 trouble has occurred. 
• The MFP control PWB has been replaced.
• The EEPROM on the MFP control PWB has been replaced.
• The scanner control PWB has been replaced.
• The EEPROM on the scanner control PWB has been replaced.
• One or more parts of the scanner (reading) section have been
replaced. 
• One or more consumables (OPC drum, developer, transfer belt)
have been replaced. 
(Copy mode image quality adjustment items)
(Copied image reference density)
If the copied test chart (UKOG-0162FCZZ) image includes a back-
ground copy of patch 3 rather than patch 2, adjust all-copy mode to the
image density level specified above.
(Copied image gamma, copied image sharpness)
Normally, default settings should be applied to 'copied image gamma'
and 'copied image sharpness', but images should be adjusted accord-
ing to user requests, if any.
1) Set the test chart (UKOG-0162FCZZ) on the original table so that it
aligns with the front frame. Then put four or five pieces of A3 (11" x
17") paper .
2) Go through the modes specified in Simulation 46-2.
ADJ 9
Adjusting the copied image 
quality
Image mode
Simulation for adjustment
All-mode 
adjustment
Individual-
mode 
adjustment
Auto mode
Binary mode
46-2
Text mode
Binary mode
46-9
Text/photo mode
Binary mode
46-10
Photo mode
Binary mode
46-11
Adjustment items
Simulation for adjustment
Copied image gamma adjustment 
(copier mode)
46-18
Copied image sharpness adjustment
46-31
1
2
W
10
9
Lot No. 01A
GRAY CHART
8
7
6
5
4
3
R
1
2
W
10
9
Lot No. 01A
GRAY CHART
8
7
6
5
4
3
R
Original
Copy
ADJ 9A
Adjust the binary mode copy density for 
all modes at once
Select 2, and press [START] key.
Press [START] key, 
or press [CUSTOM SETTINGS] key.
Item
Set 
range
Default
0
TRAY SELECT
Paper feed tray selection
1
COPY START
Copy START (Default)
2
EXP LEVEL
Exposure level selection
00
SIMULATION 46-2
Select other then 0 - 2, and 
press [START] key.
Press [CUSTOM SETTINGS] key. 
SIMULATION 46-2
EXP. LEVEL SETUP (2). INPUT VALUE 0-99, AND PRESS START.
3. AE 3.0
Press [START] key.
SIMULATION 46-2
EXP. LEVEL SETUP (2). NOW COPYING.
50
Press [CUSTOM SETTINGS] key, 
or terminate copying.
SIMULATION 46-2
EXP. LEVEL SETUP (2). SELECT 1-6, AND PRESS START.
(FEED TRAY)
  1. TRAY1  2. TRAY2  3. TRAY3  4. TRAY4
  5. BPT    6. LCC
Press [START] key, or 
press [CUSTOM SETTINGS] key.
1
Select 0, and 
press [START] key.
1
Select 1, 
and press 
[START] key. 
EXP. LEVEL SETUP (2). SELECT 0-6, AND PRESS START.
0. TRAY SELECT 
1
  1. COPY START
2. EXP LEVEL 
1
3. AE 3.0 
50
  4. CH 3.0 
50
5. MIX 3.0 
50
  6. PHOTO 3.0 
50
SIMULATION 46-2
EXP. LEVEL SETUP (2). SELECT 3-6, AND PRESS START.
(EXP. LEVEL SELECT)
  3. AE 3.0    4. CH 3.0
  5. MIX 3.0   6. PHOTO 3.0
1
Page of 43
Display

Click on the first or last page to see other AR-M700 (serv.man26) service manuals if exist.