Read Sharp AR-M700 (serv.man26) Service Manual online
AR-M550/M620/M700 SETTING AND ADJUSTMENTS 7 - 29
If an acceptable result is not obtained, do the following steps.
2) Repeat the process of changing the (TRAIL EDGE) adjustment
value and then pressing the Start key until attaining an acceptable
level.
level.
Repeat the above adjustments until an acceptable result is obtained.
(Front/rear frame direction image loss adjustment)
1) Set the (FRONT/REAR) adjustment value to 20 by entering "20"
into the (FRONT/REAR) adjustment value field and then pressing
the P key.
the P key.
Note that changing this adjustment value shifts the image position in
the front/rear frame direction.
the front/rear frame direction.
1) Go through the modes specified in Simulation 50-27.
2) Using the numeric keypad, enter the number that corresponds to
the scanner mode adjustment item.
3) Press the Start key
4) Enter the adjustment value using the numeric keypad.
5) Press the Start key
(The adjustment value should be changed in steps of 1.0mm.)
Scanned images must be visually checked for image loss.
Note: Make adjustments in the same manner as in ADJ 8A and ADJ
8C.
1) Go through the modes specified in Simulation 50-27.
2) Enter the number that corresponds to the fax adjustment item
using the numeric keypad.
3) Press the Start key
4) Enter the adjustment value using the numeric keypad.
5) Press the Start key
(The adjustment value should be changed in steps of 1.0mm.)
Scanned images must be visually checked for image loss.
Note: Make adjustments in the same manner as in ADJ 8A and ADJ
8C.
ADJ 8D
Adjust the image loss in scanner mode
Press [START] key.
Press [CUSTOM SETTINGS] key.
Item
Set range
Default
FAX send
1
OC (LEAD_EDGE)
OC lead edge
0 - 10
(Unit 1mm)
3
(3mm)
2
OC (FRONT/REAR)
OC side
3
OC (TRAIL_EDGE)
OC rear edge
4
SPF (LEAD_EDGE)
SPF lead edge
5
SPF (FRONT/REAR) SPF side
6
SPF (TRAIL_EDGE)
SPF rear edge
7
CIS (LEAD_EDGE)
CIS lead edge
8
CIS (FRONT/REAR)
CIS side
9
CIS (TRAIL_EDGE)
CIS rear edge
Scanner mode
10
OC (LEAD_EDGE)
OC lead edge
0 - 10
(Unit 1mm)
0
(0mm)
11
OC (FRONT/REAR)
OC side
12
OC (TRAIL_EDGE)
OC rear edge
13
SPF (LEAD_EDGE)
SPF lead edge
14
SPF (FRONT/REAR) SPF side
15
SPF (TRAIL_EDGE)
SPF rear edge
16
CIS (LEAD_EDGE)
CIS lead edge
17
CIS (FRONT/REAR)
CIS side
18
CIS (TRAIL_EDGE)
CIS rear edge
1
SIMULATION 50-27
ORIGINAL IMAGE LOSS SETTING(FAX/SCN). SELECT 1-18, AND
PRESS START.
[FAX]
1.OC(LEAD_EDGE)
0
2.OC(FRONT/REAR)
0
3.OC(TRAIL_EDGE)
0
4.SPF(LEAD_EDGE)
0
5.SPF(FRONT/REAR)
0
6.SPF(TRAIL_EDGE)
0
7.CIS(LEAD_EDGE)
0
8.CIS(FRONT/REAR)
0
9.CIS(TRAIL_EDGE)
0
[SCN]
10.OC(LEAD_EDGE)
0
11.OC(FRONT/REAR)
0
12.OC(TRAIL_EDGE)
0
13.SPF(LEAD_EDGE)
0
14.SPF(FRONT/REAR)
0
15.SPF(TRAIL_EDGE)
0
16.CIS(LEAD_EDGE)
0
17.CIS(FRONT/REAR)
0
18.CIS(TRAIL_EDGE)
0
0
SIMULATION 50-27
ORIGINAL IMAGE LOSS SETTING(FAX/SCN). INPUT 0-10, AND
PRESS START.
1.OC(LEAD_EDGE)
ADJ 8E
Adjust the image loss for images sent in
fax mode
fax mode
Press [START] key.
Press [CUSTOM SETTINGS] key.
Item
Set range
Default
FAX send
1
OC (LEAD_EDGE)
OC lead edge
0 - 10
(Unit 1mm)
3
(3mm)
2
OC (FRONT/REAR)
OC side
3
OC (TRAIL_EDGE)
OC rear edge
4
SPF (LEAD_EDGE)
SPF lead edge
5
SPF (FRONT/REAR) SPF side
6
SPF (TRAIL_EDGE)
SPF rear edge
7
CIS (LEAD_EDGE)
CIS lead edge
8
CIS (FRONT/REAR)
CIS side
9
CIS (TRAIL_EDGE)
CIS rear edge
Scanner mode
10
OC (LEAD_EDGE)
OC lead edge
0 - 10
(Unit 1mm)
0
(0mm)
11
OC (FRONT/REAR)
OC side
12
OC (TRAIL_EDGE)
OC rear edge
13
SPF (LEAD_EDGE)
SPF lead edge
14
SPF (FRONT/REAR) SPF side
15
SPF (TRAIL_EDGE)
SPF rear edge
16
CIS (LEAD_EDGE)
CIS lead edge
17
CIS (FRONT/REAR)
CIS side
18
CIS (TRAIL_EDGE)
CIS rear edge
1
SIMULATION 50-27
ORIGINAL IMAGE LOSS SETTING(FAX/SCN). SELECT 1-18, AND
PRESS START.
[FAX]
1.OC(LEAD_EDGE)
0
2.OC(FRONT/REAR)
0
3.OC(TRAIL_EDGE)
0
4.SPF(LEAD_EDGE)
0
5.SPF(FRONT/REAR)
0
6.SPF(TRAIL_EDGE)
0
7.CIS(LEAD_EDGE)
0
8.CIS(FRONT/REAR)
0
9.CIS(TRAIL_EDGE)
0
[SCN]
10.OC(LEAD_EDGE)
0
11.OC(FRONT/REAR)
0
12.OC(TRAIL_EDGE)
0
13.SPF(LEAD_EDGE)
0
14.SPF(FRONT/REAR)
0
15.SPF(TRAIL_EDGE)
0
16.CIS(LEAD_EDGE)
0
17.CIS(FRONT/REAR)
0
18.CIS(TRAIL_EDGE)
0
0
SIMULATION 50-27
ORIGINAL IMAGE LOSS SETTING(FAX/SCN). INPUT 0-10, AND
PRESS START.
1.OC(LEAD_EDGE)
Click on the first or last page to see other AR-M700 (serv.man26) service manuals if exist.