Read Sharp AR-F151 (serv.man11) Service Manual online
Main code
Sub code
Content
26
43
Side void setup
(Operation/Procedure)
1. When this simulation is executed, the currently set code number of the side void amount is displayed.
2. Enter the code number and press the start key. The setting is changed.
(Operation/Procedure)
1. When this simulation is executed, the currently set code number of the side void amount is displayed.
2. Enter the code number and press the start key. The setting is changed.
44
SPF document rear edge read setup + Fax document rear edge scan setup.
When this simulation is executed, the currently set code number is displayed. Enter the desired code number
and press the START key, and the display will be changed. The document rear edge scanning area in SPF
reduction (less than 100%) copy is changed.
and press the START key, and the display will be changed. The document rear edge scanning area in SPF
reduction (less than 100%) copy is changed.
The code number is changeable in the range of 0 – 8.
The default value is 4, and 2 mm of the document rear edge is cut.
When the value is changed by 1, the area is changed by 1 mm.
The default value is 4, and 2 mm of the document rear edge is cut.
When the value is changed by 1, the area is changed by 1 mm.
47
FAX document rear edge scan setup
When this simulation is executed, the currently set code number is displayed. Enter the desired code number
and press the print switch, and the setup is switched. The scan area at the rear edge of FAX original with SPF
is changed according to the entered code number.
Code number is in the range of 0 – 8.
The default is 4. When set to the default, the area of about 2 mm from the rear edge of the original is cut out.
When the value is changed by 1, the dimension is changed by about 1 mm.
When this simulation is executed, the currently set code number is displayed. Enter the desired code number
and press the print switch, and the setup is switched. The scan area at the rear edge of FAX original with SPF
is changed according to the entered code number.
Code number is in the range of 0 – 8.
The default is 4. When set to the default, the area of about 2 mm from the rear edge of the original is cut out.
When the value is changed by 1, the dimension is changed by about 1 mm.
30
01
Paper sensor status display
The paper sensor status is displayed with the lamps on the operation panel.
The paper sensor status is displayed with the lamps on the operation panel.
43
01
Fusing temperature setup (Normal copy)
(Operation/Procedure)
1. When this simulation is executed, the currently set code number is displayed.
2. Enter the code number and press the START key, and the setting will be changed.
(Operation/Procedure)
1. When this simulation is executed, the currently set code number is displayed.
2. Enter the code number and press the START key, and the setting will be changed.
Code number
Setting
0
0 mm
1
0.5 mm
2
1.0 mm
3
1.5 mm
4
2.0 mm *Default
5
2.5 mm
6
3.0 mm
7
3.5 mm
8
4.0 mm
9
4.5 mm
10
5.0 mm
Display
Sensor
Developer cartridge replacement lamp
Paper detection before resist (PPD1)
JAM lamp
Fusing section paper detection (PPD2)
Photoconductor cartridge replacement lamp
Paper exit paper detection (POD)
2nd cassette lamp
2nd CS paper detection (PPD3)
Zoom lamp
New drum cartridge detection (PUIS)
AE lamp
Single manual feed paper detection (MFD)
Exposure level 1 (Light) lamp
Main cassette A4 width detection (PSW1)
Exposure level 5 (Dark) lamp
2nd cassette A4 width detection (PSW2)
Code number
Set temperature (˚C)
0
175
1
180
2
185
3
190
4
195 (
∗ Default)
5
200
AR-F151
9 – 7
Click on the first or last page to see other AR-F151 (serv.man11) service manuals if exist.