Read Sharp AR-F151 (serv.man11) Service Manual online
Main code
Sub code
Content
07
01
Warm-up display and aging with jam
(Operation/Procedure)
1. When the simulation is executed, warming up is started.
2. Warm-up time is counted and displayed every second on the copy quantity display.
3. After completion of warm-up, the time count is stopped and the ready lamp is lighted.
4. Press the clear key to clear the warm-up time display, set the copy quantity, and press the START key, and
the machine will copy the set quantity repeatedly.
(Operation/Procedure)
1. When the simulation is executed, warming up is started.
2. Warm-up time is counted and displayed every second on the copy quantity display.
3. After completion of warm-up, the time count is stopped and the ready lamp is lighted.
4. Press the clear key to clear the warm-up time display, set the copy quantity, and press the START key, and
the machine will copy the set quantity repeatedly.
06
Intermittent aging
(Operation/Procedure)
1. When the simulation is executed, warming up is started.
2. After completion of warm-up, the ready lamp is lighted.
3. Set the copy quantity and press the START key, and the machine will copy the set quantity repeatedly.
4. After 3 sec of the interval time from completion of copying the set quantity, the machine will resume copying.
5. The above operation 4 is repeated.
(Operation/Procedure)
1. When the simulation is executed, warming up is started.
2. After completion of warm-up, the ready lamp is lighted.
3. Set the copy quantity and press the START key, and the machine will copy the set quantity repeatedly.
4. After 3 sec of the interval time from completion of copying the set quantity, the machine will resume copying.
5. The above operation 4 is repeated.
08
01
Developing bias
(Operation/Procedure)
When the START key is pressed, the developing bias is outputted for 30 sec.
(Operation/Procedure)
When the START key is pressed, the developing bias is outputted for 30 sec.
02
Main charger (Grid high)
(Operation/Procedure)
When the START key is pressed, the main charger output is supplied for 30 sec in the grid voltage HIGH mode.
(Operation/Procedure)
When the START key is pressed, the main charger output is supplied for 30 sec in the grid voltage HIGH mode.
03
Grid voltage (Low)
(Operation/Procedure)
When the START key is pressed, the main charger output is supplied for 30 sec in the grid voltage LOW mode.
(Operation/Procedure)
When the START key is pressed, the main charger output is supplied for 30 sec in the grid voltage LOW mode.
06
Transfer charger
(Operation/Procedure)
When the START key is pressed, the transfer charger output is supplied for 30 sec.
(Operation/Procedure)
When the START key is pressed, the transfer charger output is supplied for 30 sec.
10
None
Toner motor aging
(Operation/Procedure)
When the START key is pressed, the toner motor output is supplied for 30 sec.
(Operation/Procedure)
When the START key is pressed, the toner motor output is supplied for 30 sec.
14
None
Cancel of troubles other than U2
(Operation/Procedure)
After canceling the trouble, the simulation is also automatically canceled.
(Operation/Procedure)
After canceling the trouble, the simulation is also automatically canceled.
16
None
Cancel of U2 trouble
(Operation/Procedure)
1. When the START key is pressed, the EEPROM total counter check sum is rewritten and the trouble is
canceled.
2. After canceling the trouble, the simulation is also automatically canceled.
(Operation/Procedure)
1. When the START key is pressed, the EEPROM total counter check sum is rewritten and the trouble is
canceled.
2. After canceling the trouble, the simulation is also automatically canceled.
20
01
Maintenance counter clear
When the PRINT switch is pressed, the maintenance counter value is cleared and the value of 000000 is
displayed.
When the PRINT switch is pressed, the maintenance counter value is cleared and the value of 000000 is
displayed.
21
01
Maintenance cycle setup
The currently set maintenance cycle code is displayed (initial display), and the set data is stored.
The currently set maintenance cycle code is displayed (initial display), and the set data is stored.
22
01
Maintenance counter display
The display method is the same as the total count value display.
The display method is the same as the total count value display.
02
Maintenance preset value display
The value corresponding to the code set with SIM 21-01 is displayed. The display method is the same as the
total count value display.
The value corresponding to the code set with SIM 21-01 is displayed. The display method is the same as the
total count value display.
04
Jam total counter display
The display method is the same as the total count value display.
The display method is the same as the total count value display.
05
Total counter display
The total count value is dispalyed in 3 digits
The total count value is dispalyed in 3 digits
× 2 times repeatedly.
<Display example: 12345>
012
012
→ Blank → 345 → Blank → 012
0.7s 0.3s 0.7s 1.0s 0.7s
Code
Setup
0
3,000 sheets
1
6,000 sheets
2
9,000 sheets
3
13,000 sheets
4
18,000 sheets
5
Free (999,999 sheets)
∗ Default
AR-F151
9 – 3
Click on the first or last page to see other AR-F151 (serv.man11) service manuals if exist.