Read Sharp AR-F151 (serv.man11) Service Manual online
Main code
Sub code
Content
46
01
The value displayed after execution of this simulation can be set in the range of 0 – 99 with 50 as the center
value.
When the text mode set value is Gat3, for example, the GAMMA ADJUST register value set at Exp1 is:
Text Exp1 = Gat3 – 50 – 24
When 40 is set to Gat3, Text Exp1 = 40 – 50 – 24 = –34
Then set the GAMMA ADJUST register set value to –34.
Perform the same procedure for each mode and each Exp.
∗ The above table may subject to change.
value.
When the text mode set value is Gat3, for example, the GAMMA ADJUST register value set at Exp1 is:
Text Exp1 = Gat3 – 50 – 24
When 40 is set to Gat3, Text Exp1 = 40 – 50 – 24 = –34
Then set the GAMMA ADJUST register set value to –34.
Perform the same procedure for each mode and each Exp.
∗ The above table may subject to change.
∗ For the gradient, there is a similar table, though not specified here. The value set with SIM 46, however, is
not reflected.
∗ The AE mode Exp selection is not specified, but corresponds to the grades for AE exposure selection in the
former models.
not reflected.
∗ The AE mode Exp selection is not specified, but corresponds to the grades for AE exposure selection in the
former models.
12
FAX density overall adjustment
Used to set the normal mode density setup value added with each FAX resolution mode correction value to
each FAX resolution mode collectively.
(Operating procedure)
When this simulation is executed, warming up and shading are performed and the currently set value is
displayed in 2 digits. (Center value: 50)
Change the set value with the value up-down key and press the PRINT switch. The entered value is stored and
the simulation is terminated.
During this mode, the resolution mode cannot be selected.
Used to set the normal mode density setup value added with each FAX resolution mode correction value to
each FAX resolution mode collectively.
(Operating procedure)
When this simulation is executed, warming up and shading are performed and the currently set value is
displayed in 2 digits. (Center value: 50)
Change the set value with the value up-down key and press the PRINT switch. The entered value is stored and
the simulation is terminated.
During this mode, the resolution mode cannot be selected.
The range of values dispalyed after execution of this simulation is 0 - 99 with 50 as the center.
∗ when reading FAX, the AE denisty can be selected in three levels (Dark, Normal, Light). However, in this
mode, copying is made in Normal. (There is no manual setup in reading FAX.)
13
FAX density adjustment (Normal mode)
Used to set the denisty set value in the normal mode individually.
(Operating procedure)
Same as the FAX density overall adjustment.
Used to set the denisty set value in the normal mode individually.
(Operating procedure)
Same as the FAX density overall adjustment.
14
FAX denisty adjustment (Small character mode)
Used to set the denisty set value in the small character mode individually.
(Operating procedure)
Same as the FAX density overall adjustment.
Since, however, the small character mode has the Text document mode and the Photo document mode,
changeover can be made with the copy mode select key and the set value of the selected mode is displayed on
the copy quantity display. The copy mode setup is made as shown below.
Used to set the denisty set value in the small character mode individually.
(Operating procedure)
Same as the FAX density overall adjustment.
Since, however, the small character mode has the Text document mode and the Photo document mode,
changeover can be made with the copy mode select key and the set value of the selected mode is displayed on
the copy quantity display. The copy mode setup is made as shown below.
15
FAX density adjustment (Fine mode)
Used to set the denisty set value in the fine mode individually.
(Operating procedure)
Same as the FAX density overall adjustment.
Used to set the denisty set value in the fine mode individually.
(Operating procedure)
Same as the FAX density overall adjustment.
16
FAX density adjustment (Fine (300dpi) mode)
Used to set the denisty set value in the fine (300dpi) mode individually.
(Operating procedure)
Same as the FAX density overall adjustment.
Used to set the denisty set value in the fine (300dpi) mode individually.
(Operating procedure)
Same as the FAX density overall adjustment.
Relationship between the displayed values and the GAMMA ADJUST register
Exp1
Exp2
Exp3
Exp4
Exp5
AE
–24
–12
0
+12
+24
TEXT
–24
–12
0
+12
+24
PHOTO
–24
–12
0
+12
+24
T/S
–24
–12
0
+12
+24
Mode
Display lamp
Text document mode
AE mode lamp
Photo document mode
Photo mode lamp
AR-F151
9 – 9
Click on the first or last page to see other AR-F151 (serv.man11) service manuals if exist.