Read Sharp AR-C170 (serv.man26) Service Manual online
AR-C170M SIMULATION 9 - 63
2. Press the [SETUP] key.
3. Set the color patch image (adjustment pattern) paper printed in
3. Set the color patch image (adjustment pattern) paper printed in
the copy color balance adjustment (manual adjustment) (SIM
46-21) mode on the document table.
46-21) mode on the document table.
4. Press the [EXECUTE] key. The color patch image (adjustment
pattern) is read.
5. Press the REPEAT key and perform procedure 4 again.
6. Press the [OK] key.
The color balance corresponding to the color patch image
(adjustment pattern) printed in the copy color balance adjustment
(manual adjustment) is set as the service target.
6. Press the [OK] key.
The color balance corresponding to the color patch image
(adjustment pattern) printed in the copy color balance adjustment
(manual adjustment) is set as the service target.
2. Set the copied SIT chart on the document table.
3. Enter the simulation 63-9 mode.
4. Press the [EXECUTE] key.
The color coefficient automatic adjustment pattern reading is
started to calculate and display the color coefficient data. The
color coefficient data of each color can be displayed with the color
key.
3. Enter the simulation 63-9 mode.
4. Press the [EXECUTE] key.
The color coefficient automatic adjustment pattern reading is
started to calculate and display the color coefficient data. The
color coefficient data of each color can be displayed with the color
key.
2. When the [YES] key is pressed, the color balance value is set
to the default.
63
-07
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set the target color balance (gamma) for
auto color balance adjustment. The standard color
balance (gamma) or an optional color balance
(gamma) is set as the service target.
auto color balance adjustment. The standard color
balance (gamma) or an optional color balance
(gamma) is set as the service target.
Section
Image process (ICU)
Item
Picture quality
Color balance
Operation/
Procedure
Procedure
1. In the copy color balance adjustment (manual
adjustment) (SIM 46-21) mode, the color patch
image (adjustment pattern) is outputted. (This
must be adjusted properly.)
image (adjustment pattern) is outputted. (This
must be adjusted properly.)
63
-08
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set the service target of the automatic color
balance adjustment (SIM 46-24) and the automatic
color balance adjustment target of the key operator
program to the same balance as the factory target of
the automatic color balance adjustment (SIM 46-24).
balance adjustment (SIM 46-24) and the automatic
color balance adjustment target of the key operator
program to the same balance as the factory target of
the automatic color balance adjustment (SIM 46-24).
Section
Scanner (reading)
Item
Picture quality
Color balance
Operation/
Procedure
Procedure
1. Press the [EXECUTE] key.
2. Press the [YES] key.
With the above procedures, the service target of the
automatic color balance adjustment (SIM 46-24) and
the automatic color balance adjustment target of the
key operator program are set to the same level as
the factory target of the automatic color balance
adjustment (SIM 46-24).
2. Press the [YES] key.
With the above procedures, the service target of the
automatic color balance adjustment (SIM 46-24) and
the automatic color balance adjustment target of the
key operator program are set to the same level as
the factory target of the automatic color balance
adjustment (SIM 46-24).
63
-09
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to adjust the CCD gamma (CCD calibration)
(copy document mode).
(copy document mode).
Section
Scanner (reading)
Item
Picture quality
Color balance
Operation/
Procedure
Procedure
1. Set the SIT chart (UKOG-0280FCZZ) on the
document table, and make a copy in the manual
photo mode.
photo mode.
63
-10
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set the copy document mode color balance
(gamma) default.
(gamma) default.
Section
Scanner (Image scanning)
Item
Picture quality
Color balance
Operation/
Procedure
Procedure
1. Press the [EXECUTE] key, and the [YES] and
[NO] keys become active.
63
-11
Purpose
Setting
Function
(Purpose)
(Purpose)
Used to set the factory color balance in the
automatic color balance adjustment (SIM 46-24).
automatic color balance adjustment (SIM 46-24).
Section
Scanner (reading)
Item
Picture quality
Operation/
Procedure
Procedure
There are three kinds of color balance targets.
Select an optional color balance target.
This setting is applied to the factory target only.
Select an optional color balance target.
This setting is applied to the factory target only.
Display
Content
NOTE
DEF1
Color balance with emphasis on color
reproduction (factory setting)
reproduction (factory setting)
Default
DEF2
Color balance with slightly strong Cyan
DEF3
Color balance with emphasis on Cyan
Click on the first or last page to see other AR-C170 (serv.man26) service manuals if exist.