Read Sharp AR-C170 (serv.man26) Service Manual online
AR-C170M SIMULATION 9 - 5
24
4
Used to reset the maintenance
counter.
counter.
Data clear
Counter
Maintenance
6
Used to clear the copy counters.
Data clear
Counter
7
Used to clear the OPC drum
(membrane decrease) correction
counter. (This simulation is
performed with the OPC drum is
replaced.)
(membrane decrease) correction
counter. (This simulation is
performed with the OPC drum is
replaced.)
Data clear
Process
(Photoconductor,
developing, transfer,
cleaning)
(Photoconductor,
developing, transfer,
cleaning)
Photoconductor
Counter
Photoconductor
8
Used to clear the waste toner
counter in the transfer section.
counter in the transfer section.
Data clear
Process
(Photoconductor,
developing, transfer,
cleaning)
(Photoconductor,
developing, transfer,
cleaning)
Transfer
Counter
9
Used to clear the printer mode
counter and the self-print mode print
counter. (After completion of
maintenance, the counters are
cleared.)
counter and the self-print mode print
counter. (After completion of
maintenance, the counters are
cleared.)
Data clear
Printer
Counter
Printer
10
Used to clear the FAX counter.
(When the FAX is installed)
(When the FAX is installed)
Data clear
FAX
Counter
15
Used to clear the network scanner
counter.
counter.
Data clear
Scanner section
Counter
25
1
Used to check the operation of the
process section (excluding the
image process section) and the
toner remaining quantity sensor.
(The toner remaining quantity sensor
output can be monitored.)
process section (excluding the
image process section) and the
toner remaining quantity sensor.
(The toner remaining quantity sensor
output can be monitored.)
Operation test/check
Process
(Photoconductor,
developing, transfer,
cleaning)
(Photoconductor,
developing, transfer,
cleaning)
Operation
26
2
1. Used to set the paper size of the
large capacity tray. (When the
paper size is changed, the
software setup must be changed
accordingly with this simulation.)
paper size is changed, the
software setup must be changed
accordingly with this simulation.)
2. Used to detect 8.5 " x 13" (INCH
Series) paper or documents and
to set the display mode. (All
paper feed modes)
to set the display mode. (All
paper feed modes)
3. Used to set the display form of
the paper kind in the manual
paper feed mode.
paper feed mode.
Setting
Paper feed
Specifications
3
Used to set the auditor specification
mode. Setting must be made
according to the use conditions of
the auditor.
mode. Setting must be made
according to the use conditions of
the auditor.
Setting
Auditor
Specifications
5
Used to set the count mode of the
total counter and the maintenance
counter.
total counter and the maintenance
counter.
Setting
Specifications
Counter
6
Used to set the destination
specifications (paper, fixed copy
magnification ratios, image
(process) correction, machine
operation in case of an error, etc.).
specifications (paper, fixed copy
magnification ratios, image
(process) correction, machine
operation in case of an error, etc.).
Setting
Specifications
Destination
10
Used to set the trial mode of the
network scanner.
network scanner.
Setting
Scanner
Specifications
18
Used to set YES/NO of toner save
operation. (This simulation is Enable
only for Japan and UK versions. It
depends on SIM 26-6 (Destination)
setting.
For the other destinations, the same
setting can be made by the user
program P22. (Effective only in the
monochrome copy mode)
operation. (This simulation is Enable
only for Japan and UK versions. It
depends on SIM 26-6 (Destination)
setting.
For the other destinations, the same
setting can be made by the user
program P22. (Effective only in the
monochrome copy mode)
Setting
Specifications
Operation mode
(Common)
(Common)
35
Used to set whether the trouble
history display by SIM 22-4 is
displayed as one trouble or as the
accumulated number of continuous
troubles when two or more troubles
of same kind occur continuously.
history display by SIM 22-4 is
displayed as one trouble or as the
accumulated number of continuous
troubles when two or more troubles
of same kind occur continuously.
Setting
Specifications
38
Used to set "Continue/Stop" of
printing when the maintenance
timing (replacement timing of each
consumable part) is reached.
printing when the maintenance
timing (replacement timing of each
consumable part) is reached.
Setting
Specifications
41
Used to set Enable/Disable of AMS
operation in the center-binding
mode.
operation in the center-binding
mode.
Setting
Specifications
49
Used to set the copy speed mode.
Setting
Specifications
Operation mode
Code
Function (Purpose)
Purpose
Section
Item
Main
Sub
Click on the first or last page to see other AR-C170 (serv.man26) service manuals if exist.