Read Sharp AR-235 (serv.man9) Service Manual online
AR-235/275 SIMULATION - 38
Operation/procedure
SRAM data in FAST area is intialized.
Note: Executable only when the FAX is installed.
Operation/procedure
The detection test of signals is performed and the test result is dis-
played.
played.
1.
Detected signal
CI displays the detected ring pattern simultaneously.
2.
Display combination
The display conforms to the detection frequency and pattern specified
according to each country information.
according to each country information.
The detection signal level conforms to the range set by the soft SW.
The detected table and routines are shared with actual communica-
tions.
tions.
Note: Executable only when the FAX is installed.
Operation/procedure
• The pseudo-ringer sound is provided in both of the main speaker
and the external telephone.
• Holding the handset or the external telephone set stops the bell.
Hanging it restarts ringing. This operation is continued until the inter-
ruption command is supplied by pressing the [BACK] key.
ruption command is supplied by pressing the [BACK] key.
• The LCD displays the TEL/LIU status, indicating the HOOK condi-
tion.
• During sending the pseudo-ringer, RBT (Ring Back Tone) is deliv-
ered to the line.
• The bell is ON for 1sec and OFF for 2sec. When off-hooking with the
bell ON, the HOOK detection at pseudo-ringer ringing can be
checked. When off-hooking with the bell OFF, the HOOK detection
before pseudo-ringer ringing can be checked.
checked. When off-hooking with the bell OFF, the HOOK detection
before pseudo-ringer ringing can be checked.
Note: Executable only when the FAX is installed.
Operation/procedure
Used to save the SRAM data to the expanded memory and read it.
When reading, however, the current FAX software version and the
header FAX software version are collated together. If they are not iden-
tical, reading cannot be performed.
header FAX software version are collated together. If they are not iden-
tical, reading cannot be performed.
1.
Back-up targets
2.
Internal process
1) Used to check if the installed expansion memory is ready to use.
If an expanded memory is available, write the target data of the
SRAM.
SRAM.
2) After completion of writing, management information is written to
the management information block.
3) For the management information, refer to the table below.
However, the FAX program version No. area is written into the data
version no. area (FFF0 - FFFF).
version no. area (FFF0 - FFFF).
*TEST pattern
Recognized that the card normally reads the next data.
In normal cases, when installation of an expanded memory is detected
after turning ON the power, the expanded memory is cleared. When,
however, there are some SRAM data in the expanded memory, it must
not be cleared. When the ROM data name (FED0 - FFDF) in the man-
agement information of the expanded memory is "REGISTRATION,"
the expanded memory is not cleared.
after turning ON the power, the expanded memory is cleared. When,
however, there are some SRAM data in the expanded memory, it must
not be cleared. When the ROM data name (FED0 - FFDF) in the man-
agement information of the expanded memory is "REGISTRATION,"
the expanded memory is not cleared.
66-50
Purpose
Adjustment/Setting/Check
Function
(Purpose)
(Purpose)
FAST SRAM clear
66-51
Purpose
Adjustment/Setting/Check
Function
(Purpose)
(Purpose)
Signal detection check
Related soft SW
SW13-3, 4 (call sound volume)
SW32-1 to 4 (Distinctive Ring)
SW12-6, 7 (CI detection pattern)
(00:4 Sine wave 10:3 Sine wave 01:2 Sine wave)
SW26-3, 4 (speaker volume)
SW35-3, 4 (CI extinction maximum OFF time)
SW51-7, 8 (BT detection cycle)
SW52-1, 2 (BT/DT detection level)
SW55-1 to 7 (detection possible time of CI
signal)
SW56-5, 6 (DT, BT filter efficiency)
SW56-7 (DP, BT detection level)
SW32-1 to 4 (Distinctive Ring)
SW12-6, 7 (CI detection pattern)
(00:4 Sine wave 10:3 Sine wave 01:2 Sine wave)
SW26-3, 4 (speaker volume)
SW35-3, 4 (CI extinction maximum OFF time)
SW51-7, 8 (BT detection cycle)
SW52-1, 2 (BT/DT detection level)
SW55-1 to 7 (detection possible time of CI
signal)
SW56-5, 6 (DT, BT filter efficiency)
SW56-7 (DP, BT detection level)
Detected in off-hook.
CI, CNG, FNET, DTMF
Detected in off-hook.
BusyTone, CNG
DialTone, CED
SDT, flag, DTMF
DialTone, CED
SDT, flag, DTMF
Combination
Hook state
A
CI, CNG, FNET
On hook
B
CED, CNG, BusyTone, DTMF
Off hook
C
CED, Flag, BusyTone
D
CED, Flag, DialTone
E
CED, Flag, SDT
66-52
Purpose
Adjustment/Setting/Check
Function (Purpose)
Pseudo-ringer check
Note
Japan only
66-53
Purpose
Adjustment/Setting/Check
Function (Purpose)
SRAM backup
Target data
Registration information, soft SW information,
FAX counter information (Information for each
department is not required.)
FAX counter information (Information for each
department is not required.)
Data out of target
Image management information,
communication reservation information
communication reservation information
SRAM stack processing
Lowest
address
Area name
Content
Expanded
memory
Upper 2MB
0000 to
FFAF
FFAF
Reserved
←
FFB0 to
FFCF
FFCF
TEST pattern
TEST pattern
*Reference
FFD0 to
FFDF
FFDF
ROM data
name
name
ASCII 16 Byte
REGISTRATION
FFE0 to
FFEF
FFEF
Data version
No.
No.
ASCII 16 Byte
FAX program
version No.
FFF0 to
FFF1
FFF1
Write
complete FLG
complete FLG
ERASE=H'FFFF
Completion=H'0000
←
FFF2 to
FFF3
FFF3
SRAM clear
flag
flag
Clear/No =H'0000
Clear/Yes=H'0001
Invalid
FFF4 to
FFF7
FFF7
Start address
Data start address
←
FFF8 to
FFFB
FFFB
End address
Data end address
←
FFFC to
FFFF
FFFF
SUM
Data check sum
←
Addres
sDate
Addres
sDate
Addres
sDate
FFB0
0001
FFBC
0040
FFC8
1000
FFB2
0002
FFBE
0080
FFCA
2000
FFB4
0004
FFC0
0100
FFCC
4000
FFB6
0008
FFC2
0200
FFCE
8000
FFB8
0010
FFC4
0400
–
–
FFBA
0020
FFC6
0800
–
–
Additional process when turning on the power
Click on the first or last page to see other AR-235 (serv.man9) service manuals if exist.