Read Sharp AL-2040 (serv.man2) Service Manual online
AL-2040 SIMULATION, TROUBLE CODES 10 - 5
22
04
JAM total counter display
The display method is the same as the total count value display.
<Display example: 12345>
The display method is the same as the total count value display.
<Display example: 12345>
05
Total counter display
The total count value is displayed in 3 digits X 2 times repeatedly.
The total count value is displayed in 3 digits X 2 times repeatedly.
08
SPF counter display <SPF model only>
The display method is the same as the total count value display.
The display method is the same as the total count value display.
12
Drum counter display
The display method is the same as the total count value display.
The display method is the same as the total count value display.
14
ROM version display
The main code and the sub code of the ROM version is displayed on the value display section in 2 digits alternately.
The display method is the same as the total count value display.
The main code and the sub code of the ROM version is displayed on the value display section in 2 digits alternately.
The display method is the same as the total count value display.
16
Duplex counter display
The display method is the same as the total count value display.
The display method is the same as the total count value display.
17
Copy counter display
The display method is the same as the total count value display.
The display method is the same as the total count value display.
18
Printer counter display
The display method is the same as the total count value display.
The display method is the same as the total count value display.
19
Scanner mode counter display
The display method is the same as the total count value display.
The display method is the same as the total count value display.
21
Scanner counter display
The display method is the same as the total count value display.
The display method is the same as the total count value display.
22
SPF JAM counter display <SPF model only>
The display method is the same as the total count value display.
The display method is the same as the total count value display.
24
01
JAM total counter clear
When the PRINT switch is pressed, the JAM total count value is reset to 0.
When the PRINT switch is pressed, the JAM total count value is reset to 0.
04
SPF counter clear <SPF model only>
When the PRINT switch is pressed, the SPF count value is reset to 0.
When the PRINT switch is pressed, the SPF count value is reset to 0.
05
Duplex counter clear
When START key is pressed, the duplex count value is set to 0.
When START key is pressed, the duplex count value is set to 0.
07
Drum counter clear
When the PRINT switch is pressed, the drum count value is reset to 0.
When the PRINT switch is pressed, the drum count value is reset to 0.
08
Copy counter clear
When the PRINT switch is pressed, the copy count value is reset to 0.
When the PRINT switch is pressed, the copy count value is reset to 0.
09
Printer counter clear
When the PRINT switch is pressed, the printer count value is reset to 0.
When the PRINT switch is pressed, the printer count value is reset to 0.
13
Scanner counter clear
When the PRINT switch is pressed, the scanner count value is reset to 0.
When the PRINT switch is pressed, the scanner count value is reset to 0.
14
SPF JAM total counter clear <SPF model only>
When the PRINT switch is pressed, the SPF JAM total count value is reset to 0.
When the PRINT switch is pressed, the SPF JAM total count value is reset to 0.
15
Scanner mode counter clear
When the PRINT switch is pressed, the scanner mode counter is reset to 0.
When the PRINT switch is pressed, the scanner mode counter is reset to 0.
25
01
Main motor operation check (Cooling fan motor rotation check)
When the PRINT switch is pressed, the main motor (as well as the duplex motor in the duplex model) is operated for 30 sec. If
the developing unit is installed at that time, the developing bias, the main charger, and the grid are outputted together in order
to avoid toner consumption. Since, in this case, laser discharge is required when stopping the motor, the polygon motor is
rotated at the same time. If the developing unit is not installed, the above high voltage is not outputted and only the motor is
rotated.
When the PRINT switch is pressed, the main motor (as well as the duplex motor in the duplex model) is operated for 30 sec. If
the developing unit is installed at that time, the developing bias, the main charger, and the grid are outputted together in order
to avoid toner consumption. Since, in this case, laser discharge is required when stopping the motor, the polygon motor is
rotated at the same time. If the developing unit is not installed, the above high voltage is not outputted and only the motor is
rotated.
: Do not execute this simulation by forcibly turning ON the door ON/OFF switch.
10
Polygon motor ON
(Operation/Procedure)
When the START key is pressed, the polygon motor is operated for 30 sec.
(Operation/Procedure)
When the START key is pressed, the polygon motor is operated for 30 sec.
26
02
SPF setup
When this simulation is executed, the current setup of the SPF code number is displayed. Enter the code number
corresponding to the SPF and press the PRINT switch to enable the setup.
When this simulation is executed, the current setup of the SPF code number is displayed. Enter the code number
corresponding to the SPF and press the PRINT switch to enable the setup.
Main
code
code
Sub
code
Content
012
→ Blank → 345 → Blank → 012
0.7s
0.3s 0.7s
1.0s
0.7s
Code number
SPF
0
SPF not installed
1
SPF installed
2
RSPF installed
Click on the first or last page to see other AL-2040 (serv.man2) service manuals if exist.