LL-T2000A (serv.man9). Complete - Sharp Monitor Service Manual (repair manual). Page 8

LL-T2000A

2 – 4

Depending on the computer or OS, it may be necessary to use the
computer to operate the installation of monitor set-up information etc.
If so, follow the steps below to install the monitor set-up information.
(Depending on the type of computer or OS, command names and
methods may differ. Please follow the computer's own operation man-
ual while reading this.)

An ICC (International Color Consortium) profile is a file that describes
the color characteristics of the LCD monitor. By using an application
that works together with an ICC profile, a high color resolution can be
realized. 

•  Windows98, WindowsMe and Windows2000 all use the ICC profile.

•  When installing Windows98, WindowsMe and Windows2000 set-up

information (described below), the ICC profile is also installed. If you
would like to install the ICC program only, please refer to Installing
the ICC profile.

• When using the ICC profile, please set the [WHITE BALANCE] to

[STD] and the [COLOR MODE] to [OFF].

■

■

■

■

Installing monitor set-up information into Windows95.
This explanation assumes that the floppy disk drive is "A drive".

1.  Place the Utility Disk (provided) into the computer's A drive.

2.  Click on the [Start] button. From [Settings], choose [Control

Panel].

3.  Double click on [Display].

4.  Click on [Settings], [Advanced Properties], and [Monitor], then

[Change]. 

5.  Click on [Have disk], confirm that [Copy manufacturer's files from:]

is [A:] then click [OK].

6.  Confirm that the monitor details are selected, and click [OK].

7.  Check that the monitor details are displayed, then click [Apply].

8.  Click [OK], and close the window.

9.  Remove the Utility Disk from the A drive.

■

■

■

■

Installing monitor set-up information into Windows98, and setting the
monitor's ICC profile as a predetermined value.
This explanation assumes that the floppy disk drive is "A drive".

If the "Add new Hardware Wizard" has appeared:

1.  Place the Utility Disk (provided) into the computer's A drive.

2. Click 

[Next].

3.  Check [Display a list of all the drivers in a specific location, so you

can select the driver you want.], then click [Next].

4.  When [Models] is displayed, click on [Have disk], confirm that

[Copy manufacturer's files from:] is [A:], and click [OK].

5.  Confirm that the monitor details are selected, then click [Next],

[Next], and [Finish]. If the "Add New Hardware Wizard" appears,
repeat the installation commands beginning from 2 above.

6.  Remove the Utility Disk from the A drive.

If the "Add New Hardware Wizard" has not appeared:

1.  Place the Utility Disk in the computer's A drive.

2.  Click on the [Start] button. From [Settings], choose [Control

Panel].

3.  Double click on [Display].

4.  Click on [Settings], [Advanced] and [Monitor].

5.  In [Options], check [Automatically detect Plug & Play monitors]

and click on [Change].

6.  Click [Next].

7.  Click on [Display a list of all the drivers in a specific location, so

you can select the driver you want.], then click [Next].

8.  When [Models] is displayed, click on [Have disk], confirm that

[Copy manufacturer's files from:] is [A:], and click [OK].

9.  Confirm that the monitor details are selected, then click [Next],

[Next], and [Finish].

10.  Check that the monitor details are displayed, then click [Apply].

11.  Click [OK], and close the window.

12.  Remove the Utility Disk from the A drive. 

■ 

■ 

■ 

■ 

Installing monitor set-up information into Windows2000, and setting
the monitor's ICC profile as a predetermined value.
This explanation assumes that the floppy disk drive is "A drive".

1.  Place the Utility Disk (provided) into the computer's A drive.

2.  Click on the [Start] button. From [Settings], choose [Control

Panel].

3.  Double click on [Display].

4.  Click on [Settings], [Advanced] and [Monitor].

5.  Click on [Properties], [Driver] and [Update Driver].

6.  When [Upgrade Device Driver Wizard] appears, click [Next].

7.  Check [Display a list of the known drivers for this device so that I

can choose a specific driver] and click [Next].

8.  When [Models] is displayed, click on [Have disk], confirm that

[Copy manufacturer's files from:] is [A:], and click [OK].

9.  Select the monitor from the list displayed and click [Next].

10. Click [Next], confirm that the monitor's name appears on the

screen, and click [Finish]. If [The Digital Signature Not Found]
appears, click [Yes].

11.  Click on [Close].

12.  Click [OK], and close the window.

13.  Remove the Utility Disk from the A drive.

■

■

■

■

Installing monitor set-up information into WindowsMe, and setting the
monitor's ICC profile as a predetermined value.
This explanation assumes that the floppy disk drive is "A drive".

If the "Add new Hardware Wizard" has appeared:

1.  Place the Utility Disk (provided) into the computer's A drive.

2.  Check [Specify the location of the driver [Advanced]] and click

[Next].

3.  Check [Display a list of all the drivers in a specific location, so you

can select the driver you want.], then click [Next].

4.  When [Models] is displayed, click on [Have disk], confirm that

[Copy manufacturer's files from:] is [A:], and click [OK].

5.  Select the monitor details from the list, then click [Next], [Next],

and [Finish]. If the "Add new Hardware Wizard" appears, repeat
the installation commands beginning from 2 above.

6.  Remove the Utility Disk from the A drive.

If the "Add New Hardware Wizard" has not appeared:

1.  Place the Utility Disk in the computer's A drive.

2.  Click on the [Start] button. From [Settings], choose [Control

Panel].

3.  Double click on [Display].

4.  Click on [Settings], [Advanced] and [Monitor].