Read Sharp LB-1085 (serv.man2) Parts Guide online
LB-1085
DISASSEMBLY AND ASSEMBLY
4 – 12
4. LCD MODULE DISASSEMBLY AND ASSEMBLY
Note: If the protection panel is installed, remove it before attaching the open/close caster jig.
1) Remove the rear cover left. (Refer to “
■ Rear cabinet right, Rear cabinet left disassembly and assembly”)
2) Pull up the actuator on the FPC connector, and disconnect the FPC.
Remove 3 screws (M5 x 10). (Refer to step 4 in “
■ Backlight PWB disassembly and assembly”)
3) Attach the Caster jig for open/close with 4 screws.
Side view
Support Legs
Support Legs
㪥㫆㫋㪼㩷㪈㪑㩷㪤㫆㪻㫀㪽㫐㫀㫅㪾㩷㫋㪿㪼㩷㫊㫋㪸㫅㪻㩷㪽㫉㫆㫄㩷㪫㫐㫇㪼㩷㪩㩷㩿㫎㪿㪼㫅㩷㪻㪼㫃㫀㫍㪼㫉㪼㪻㪀㩷㫋㫆㩷㪫㫐㫇㪼㩷㪣
㪥㫆㫋㪼㩷㪈㪑㩷㪤㫆㪻㫀㪽㫐㫀㫅㪾㩷㫋㪿㪼㩷㫊㫋㪸㫅㪻㩷㪽㫉㫆㫄㩷㪫㫐㫇㪼㩷㪩㩷㩿㫎㪿㪼㫅㩷㪻㪼㫃㫀㫍㪼㫉㪼㪻㪀㩷㫋㫆㩷㪫㫐㫇㪼㩷㪣
Servicing stand
Spacer lock screw
Hole on the right of the angle
Spacer-side counter-bored hole
The R marking gets hidden and the L marking appears instead.
Tighten up the spacer lock screw.
Remove the
spacer lock screw.
Spacer lock screw
Marked "R"
Marked "R"
Spacer
㪥㫆㫋㪼㩷㪉㪑㩷㪝㫆㫉㩷㪽㫀㫋㫋㫀㫅㪾㩷㫆㫅㩷㫋㪿㪼㩷㪹㪼㫑㪼㫃㩷㫊㫀㪻㪼㪃㩷㫌㫊㪼㩷㪸㩷㫊㪿㫆㫉㫋㪼㫉㩷㫋㫆㫆㫃㩷㫆㫉㩷㪸㩷㫃㫆㫅㪾㪄㫋㫀㫇㩷㫋㫆㫆㫃㪅
㪥㫆㫋㪼㩷㪉㪑㩷㪝㫆㫉㩷㪽㫀㫋㫋㫀㫅㪾㩷㫆㫅㩷㫋㪿㪼㩷㪹㪼㫑㪼㫃㩷㫊㫀㪻㪼㪃㩷㫌㫊㪼㩷㪸㩷㫊㪿㫆㫉㫋㪼㫉㩷㫋㫆㫆㫃㩷㫆㫉㩷㪸㩷㫃㫆㫅㪾㪄㫋㫀㫇㩷㫋㫆㫆㫃㪅
㪲㩷㪫㫐㫇㫀㪺㪸㫃㩷㫊㪼㫋㫌㫇㩷㪴
㪥㫆㫋㪼㩷㪊㪑㩷㪮㫀㫋㪿㩷㫋㪿㪼㩷㫊㫋㪸㫅㪻㩷㫀㫅㩷㫇㫃㪸㪺㪼㪃㩷㪹㪼㩷㫊㫌㫉㪼㩷㫋㫆㩷㫃㫆㪺㫂㩷㫋㪿㪼㩷㫊㫋㪸㫅㪻㩷㪺㪸㫊㫋㪼㫉㫊㪅
㪥㫆㫋㪼㩷㪊㪑㩷㪮㫀㫋㪿㩷㫋㪿㪼㩷㫊㫋㪸㫅㪻㩷㫀㫅㩷㫇㫃㪸㪺㪼㪃㩷㪹㪼㩷㫊㫌㫉㪼㩷㫋㫆㩷㫃㫆㪺㫂㩷㫋㪿㪼㩷㫊㫋㪸㫅㪻㩷㪺㪸㫊㫋㪼㫉㫊㪅
㪣㫆㫅㪾㪄㫋㫀㫇㩷㫋㫆㫆㫃
㪝㫀㫏㫀㫅㪾㩷㫊㫇㫆㫋㫊
㩿㪤㪌㩷㫊㪺㫉㪼㫎㫊㪀
㪪㪿㫆㫉㫋㪼㫉㩷㫋㫆㫆㫃
Remove the spacer lock
screw from the stand (Type
R when delivered).
(Two locations in total: one
each at top and bottom)
screw from the stand (Type
R when delivered).
(Two locations in total: one
each at top and bottom)
Ԙ
Shift the spacer to the right and align the spacer-side counter-
bored hole with the hole on the right of the angle.
bored hole with the hole on the right of the angle.
ԙ
Apply the spacer lock screw in position.
(The stand is now modified as Type L.)
(The stand is now modified as Type L.)
Ԛ
㪙㪼㫑㪼㫃㩷㫊㫀㪻㪼㩷㪹㫆㫊㫊
㩿㪽㫆㫉㩷㫇㫆㫊㫀㫋㫀㫆㫅㫀㫅㪾㪀
㩿㪽㫆㫉㩷㫇㫆㫊㫀㫋㫀㫆㫅㫀㫅㪾㪀
Click on the first or last page to see other LB-1085 (serv.man2) service manuals if exist.