Read Sharp XE-A201 (serv.man4) Service Manual online
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
for after sales service only.
The contents are subject to change without notice.
SHARP CORPORATION
q
SERVICE MANUAL
CODE :
CONTENTS
Parts marked with "
!
" are important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
Top and Bottom of a Page :
-38.1mm
00ZXEA201VSME
ELECTRONIC
CASH REGISTER
CASH REGISTER
SRV KEY : Not necessary
PRINTER : M-T51
(V version)
PRINTER : M-T51
(V version)
MODEL
XE-A201
CHAPTER 1.
CHAPTER 2.
CHAPTER 3.
CHAPTER 4.
CHAPTER 5.
CHAPTER 6.
CHAPTER 7.
SPECIFICATIONS...................................................................... .....1
OPTIONS......................................................................................... 5
MASTER RESET AND PROGRAM RESET.................................... 5
HARDWARE DESCRIPTION........................................................... 6
TEST FUNCTION............................................................................12
IPL (INITIAL PROGRAM LOADING) FUNCTION...........................15
CIRCUIT DIAGRAM AND PWB LAYOUT.......................................17
PARTS GUIDE
XE-A201VS SPECIFICATIONS
– 1 –
CHAPTER 1. SPECIFICATIONS
1. APPEARANCE
2. RATING
3. KEYBOARD
1) KEYBOARD LAYOUT
2) KEY LIST
■
■
■
■
Keyboard layout
Note: The small characters on the bottom or lower right in each key
indicates functions or characters which can be used for charac-
ter entries for text programming.
■
■
■
■
Key names
4. MODE SWITCH
1) LAYOUT
• Rotary type
The mode switch can be operated by inserting one of the two supplied
mode keys - manager (MA) and operator (OP) keys. These keys can
be inserted or removed only in the “REG” or “OFF” position.
be inserted or removed only in the “REG” or “OFF” position.
XE-A201
Weight
16.8lb (7.6kg)
Dimensions
330 (W) x 428 (D) x 280 (H) mm
13.0 (W) x 16.9 (D) x 11.0 (H) inches
13.0 (W) x 16.9 (D) x 11.0 (H) inches
Power source
AC 240V (
m
10%), 60Hz
Power consumption
Stand-by 7W, Operating 34.5W (max.)
Working temperature
0°C~40°C (32°F to 104°F)
Type
Normal keyboard
Key position
STD/MAX 53
Key pitch
19 (W) x 19 (H) mm
Key layout
Fixed type
RS-232C connector
Operator display
Receipt paper
Drawer lock
Drawer
Printer cover
Customer display
(Pop-up type)
(Pop-up type)
Mode switch
Power cord
Keyboard
Front view
Rear view
KEY TOP
DESCRIPTION
2
Paper feed key
RA
Received-on account key
RCPT/PO
Receipt print/Paid-out key
p
Void key
ESC
Escape key
EX
Foreign currency exchange key
%1, %2
Percent 1 and 2 keys
RF
Refund key
-
Discount key
y
Multiplication key
n
Decimal point key
CL
Clear key
00, 0~9
Numeric keys
PLU/SUB
PLU/Subdepartment key
DEPT #
Department code entry key
DEPT SHIFT
Department shift key
CLK#
Clerk code entry key
1-17~16-32
Department keys
AMT
Amount key
AUTO
Automatic sequence key
VAT
Value added tax key
CR1, CR2
Credit 1 and 2 keys
CH
Cheque key
#/TM/ST
Non-add code/Time display/Subtotal key
TL/NS
Total/No sale key
PGM
OP
X/Z
REG
MGR
X
1
/Z
1
X
2
/Z
2
OP
MA
Manager key (MA)
Operator key (OP)
MA
OP
XE-A201VS SPECIFICATIONS
– 2 –
The mode switch has these settings:
q
:
This mode locks all register operations. (AC power turns off.)
No change occurs to register data.
No change occurs to register data.
OP X/Z: To take individual clerk X or Z reports, and to take flash
reports.
It can be used to toggle receipt state “ON” and “OFF” by
pressing he [RCP/PO] key.
pressing he [RCP/PO] key.
REG:
For entering sales.
PGM:
To program various items.
p
:
Enters into the void mode. This mode allows correction after
finalizing a transaction.
finalizing a transaction.
MGR:
For manager’s entries. The manager can use this mode for
an override entry.
an override entry.
X1/Z1: To take the X/Z report for various daily totals.
X2/Z2: To take the X/Z report for periodic (weekly or monthly) con-
solidation.
5. DISPLAY
1) OPERATOR DISPLAY
Display device
: LED numeric display
Number of line
: 1 line
Number of positions : 10 positions numeric display
Color of display
: Yellow / Green
Character form
: 7 segment + DP
Character size
: Numeric 14.2 (H) x 7.9 (W) mm
Layout:
2) CUSTOMER DISPLAY
Display device
: LED
Number of line
: 1 line
Number of positions : 7 positions
Color of display
: Yellow / Green
Style
: Pop up type
Character form
: 7 segment + Dp
Character size
: 14.2mm (H) x 7.9mm (W)
Layout:
Amount: Appears in the far-right eight (max.) positions. When the
amount is negative, the minus symbol "-" appears before the
amount.
amount.
Number of repeats for repetitive registrations:
The number of repeats is displayed, starting at "2" and incre-
mental with each repeat. When you have registered ten times,
the display will show "0." (2
the display will show "0." (2
3
3 .... 9
3
0
3
1
3
2 ... )
Receipt function status:
The indicator "_" appears in the RCPT OFF position when the
receipt function is in the OFF status.
Time:
Appears in the second to sixth positions (using 24-hour for-
mat) in the OP X/Z, REG or MGR mode. In the REG or MGR
mat) in the OP X/Z, REG or MGR mode. In the REG or MGR
mode, press the [#/TM/ST] key to display the time.
■
■
■
■
Machine state symbols
:
Appears during programming.
:
Appears when an error is detected.
:
Appears when the subtotal is displayed or when the amount
tendered is smaller than the sales amount.
:
Appears when the [EX] key is pressed to calculate a subtotal in
foreign currency.
:
Appears when a transaction is finalized by pressing the [TL/
NS], [CH], [CR1] or [CR2] key.
NS], [CH], [CR1] or [CR2] key.
:
Appears when the change due amount is displayed.
: Appears in the far-left three positions at the timing of key entry
when the electronic journal (EJ) memory is full. (Depending on
programming.)
:
Appears when the voltage of the installed batteries is under the
required level. You must replace with new ones within two
days. Refer to page 63 for details.
days. Refer to page 63 for details.
:
Appears when the batteries are not installed, or the installed
batteries are dead. You must replace with new ones immedi-
ately. Refer to page 63 for details.
:
May appear right below the eighth and ninth places at the tim-
ing of finalization of a transaction when the electronic journal
ing of finalization of a transaction when the electronic journal
(EJ) memory is nearly full.
Also appears right below the tenth place when power save
mode is effective.
mode is effective.
: Appearss when programmed date (and time) for EURO modifi-
cation operation is come.
:
Appears when the print head release lever is in the lifted posi-
tion.
:Appears when the paper is out.
0 . 1 . 2 . 3 . 4 . 5 . 6 . 7 . 8 . 9 .
3 . 4 . 5 . 6 . 7 . 8 . 9 .
Operator display
Customer display (Pop-up type)
PLU/SUB
DEPT REPEAT
RCPT
OFF
NUMBER
SHIFT
DC
Clerk code
XE-A201VS SPECIFICATIONS
– 3 –
Segment
Decimal Point
6. PRINTER
1) Printer
• Part number
: M-T51
• NO. of station
: 1 (Receipt or journal)
• Validation
: No.
• Printing system
: Line thermal
• No. of dot
: 288 dots
• Dot pitch
: Horizontal 0.167mm
Vertical
0.174mm
• Font
: 10 dots (W)
u
24 dots (H)
• Printing capacity : max. 24 characters
• Character size
: 1.67mm (W)
u
4.17mm (H) at 10
u
24 dots
• Print pitch
: Column distance
2.0mm
Row distance
5.21mm
• Print speed
: Approximate 52mm/s (Approximate 10 l/s)
• Paper feed speed : Approximate 52mm/s (Approximate 10 l/s)
(Manual feed)
: Approximate 52mm/s (Approximate 10 l/s)
• Reliability
: Mechanism LIFE 6 million lines used to high-
quality thermal paper
• Paper end sensor : Set up
• Cutter
: Manual Cutter
• Near end sensor : No
2) Paper
• Paper roll dimension : 57.5
m
0.5mm
in width
Max. 80mm
in diameter
• Paper quality
: High-quality thermal paper
paper thickness: 0.06 to 0.08mm
Nihon seisi thermal paper : TF50KS-E
Oji thermal paper
Oji thermal paper
: PD150R,
PD160R
3) Logo stamp
• No
4) Printing area
Number of thermal head heater elements 288 dots
Display
position
Description
Amount
1-8
Minus sign
2-10
-: Floating
Error
8-10
Exx:xx = error code
PGM Mode
10
P
CASH, CHECK,
CHARGE
CHARGE
10
F: Light up when a registration is
finalized by depressing CASH,
CHECK, CHARGE key
finalized by depressing CASH,
CHECK, CHARGE key
SUB TOTAL/
short tender
short tender
10
o
Change
10
C: Light up whenever the change
due amount appears in the display.
due amount appears in the display.
Currency
Conversion
Conversion
10
c: Light up whenever the foreign
amount appears in the display.
amount appears in the display.
Department
9-10
No zero-suppressed
PLU
7-10
No zero-suppressed
Repeat
8
Endless count, starting from 2.
Receipt OFF
9
_
DC
_: Double size character entry sta-
tus
tus
SHIFT
_: Shift character entry status
NUMBER
_: Number character entry status
Clerk No.
2, 3
-xx-: clerk number
EJ FULL
8-10
E-E: Light up when EJ memory is
FULL at the timing of key entry (by
PGM selection).
FULL at the timing of key entry (by
PGM selection).
Low Battery
10
L:
No Battery
10
L
:
Display
position
Description
Decimal point
7-1
TAB
4-1
EJ near full
8, 9
(by PGM selection)
0.167
(4.75)
(4.75)
48 (288 dots)
print area
(max.24 characters)
(units : mm)
57.5±0.5
(Paper dimension)
