Read Sharp XL-30 (serv.man2) User Guide / Operation Manual online
15
RADIO OPERATION
To enter stations into memory:
1
Perform steps 1 - 6 in the “Tuning” section.
2
Press the MEMORY/SET button.
●
“MEMORY” will flash.
3
Within 5 seconds, turn the jog dial to make the
preset channel number flash in the display.
preset channel number flash in the display.
●
Store the stations in memory, in order, starting
with preset channel 1.
with preset channel 1.
4
Within 5 seconds, press the MEMORY/SET
button to store that station in the selected sta-
tion preset number memory.
button to store that station in the selected sta-
tion preset number memory.
●
If the “MEMORY” and preset number indicators
go out before the station is memorised, repeat
the operation from step 2.
go out before the station is memorised, repeat
the operation from step 2.
5
Repeat steps 1 - 4 to set other preset stations,
or to change a preset station.
or to change a preset station.
After use:
Press the ON/STAND-BY button to enter the stand-
by mode.
Press the ON/STAND-BY button to enter the stand-
by mode.
■
Tuning
3,5,6
2
1
4
1
Press the ON/STAND-BY button to turn the
power on.
power on.
2
Press the FUNCTION button until “FM” or “AM”
appears in the display.
appears in the display.
3
Press the BAND button to select the desired fre-
quency band. (FM ST, FM or AM)
quency band. (FM ST, FM or AM)
4
Press the TUNING (
X
or
W
) button to tune in to
the desired station.
Manual tuning:
Press the TUNING (
X
or
W
) button as many times
as required to adjust the frequency shown on the
display to the frequency of the desired station.
display to the frequency of the desired station.
Auto tuning:
When the TUNING (
X
or
W
) button is pressed for
more than 0.5 seconds, scanning will start auto-
matically and the tuner will stop at the first receiv-
able broadcast station.
matically and the tuner will stop at the first receiv-
able broadcast station.
Notes:
●
When radio interference occurs during auto scan
tuning, auto scan tuning may stop automatically
at that point.
tuning, auto scan tuning may stop automatically
at that point.
●
If a weak station signal is found during auto scan
tuning, the station will be skipped.
tuning, the station will be skipped.
●
To stop the auto tuning, press the TUNING (
X
or
W
) button again.
5
To receive an FM stereo transmission, press the
BAND button so that the “ST” indicator on the
display lights up.
BAND button so that the “ST” indicator on the
display lights up.
●
“
j
” will appear when an FM broadcast is in
stereo.
6
If the FM reception is weak, press the BAND
button so that the “ST” indicator goes out.
button so that the “ST” indicator goes out.
●
The reception changes to monaural, the sound
becomes clearer.
becomes clearer.
Note:
●
The last station tuned in will be recalled, even
after changing the tuning band or the function,
or after switching the unit to the stand-by mode.
after changing the tuning band or the function,
or after switching the unit to the stand-by mode.
■
Preset tuning
You can store up to 30 stations in memory (30 sta-
tions consisting of any combination of FM and AM
stations you like) and recall them.
tions consisting of any combination of FM and AM
stations you like) and recall them.
3
2,4
*XL-30H(SUK)P14-P18
00.2.2, 3:57 PM
15
Click on the first or last page to see other XL-30 (serv.man2) service manuals if exist.