CD-DP2500 (serv.man2). Part 1 - Sharp Audio User Guide / Operation Manual. Page 16

Read Sharp CD-DP2500 (serv.man2) User Guide / Operation Manual online

15
(Continued)
■
Disc number selection
1

 When stopped, press the DISC SKIP button.
2

 Press the 
0
/
R
 (
 0R 
) button.
●
The next disc playback will begin, after which each fol-
lowing disc will be played sequentially.
Notes:
●
When the DISC SKIP button is pressed during playback,
playback will begin automatically from the next disc.
(It is not necessary to press the 
0
/
R
 (
 0R 
) button.)
●
When one of the disc number buttons (DISC-1 – DISC-3) is
pressed during playback, playback of the selected disc will
begin automatically.
(It is not necessary to press the 
0
/
R
 (
 0R 
) button.)
■
APSS (Auto Program Search System)
APSS automatically locates the beginning of any track.
To listen again to the track being played:
Press the 
5
  (
 5 3 
) button for less than 0.5 seconds
during playback.
To move to the beginning of the next track:
Press the 
4
  (
 2 4 
) button for less than 0.5 seconds
during playback.
●
To skip a number of tracks at one time, press the 
5
 (
 5
3 
) or 
4
 (
 2 4 
) button repeatedly until the desired
track number is shown.
●
To start playback from a desired track, press the 
5
 ( 
5 3
 )
or 
4
 (
 2 4 
) button whilst in the stop mode to select the
track number, and then press the 
0
/
R
 (
 0R 
) button.
Note:
●
APSS can only search for music on a single disc.
■
Cue and review
1
Load a disc and begin playback.
2
Hold down the 
2
 (
 2 4 
) button for audible fast for-
ward, and hold down the 
3
 (
 5 3 
) button for audible
fast reverse.
3
Normal playback will resume when the 
2
 (
 2 4 
) or
3
 (
 5 3 
) button is released.
Notes:
●
When the end of the disc is reached whilst cueing, “END”
will appear in the display and CD operation will be paused.
(Even though the next disc has been loaded, the disc will
not be switched.)
Press the 
3
 (
 5 3
 ) button for fast reverse or press the
■
 (CD 
■
) button to stop CD operation.
●
If the beginning of the disc is reached whilst reviewing, the
mode will automatically switch to normal playback at that
point.
■
Random play
(Remote control operation)
The tracks on the disc(s) can be played in random order auto-
matically.
1
Load a disc(s) and close the disc tray.
2
Press the RANDOM button to begin random play.
●
“R” will appear.
Notes:
●
If you press the 
4
 ( 
2 4
 ) button during random play,
you can move to the next track. On the other hand, the 
5
( 
5 3
 ) button does not allow you to move to the previ-
ous track. The beginning of the track being played will be
located.
●
When using random play, be sure to press the 
■
 (CD 
■
)
button after you are through listening.
Otherwise, the disc(s) will play continuously.
●
In random play the unit will select and play tracks automati-
cally. (You cannot select the order of the tracks.)
To cancel random play:
Press the 
0
/
R
 ( 
0R
 ) button.
●
 “R” will go out.
Caution:
●
Do not carry the unit with discs left in the disc trays.
The discs may come loose inside the unit and they
may be damaged or cause damage to the unit. This
may also cause malfunctions.
●
Do not place two CDs in one disc position.
●
Do not push the disc tray whilst it is moving.
●
Do not attempt to turn the disc tray by hand. This may
cause malfunctions.
●
If the power fails whilst the tray is open, wait until the
power is restored.
●
If the disc tray is stopped forcibly, “ERR” will appear in
the display and the unit will not function.
If this occurs, press the ON/STAND-BY button to enter
the stand-by mode and then turn the power on again.
●
If TV or radio interference occurs during CD operation,
move the unit away from the TV or radio.
●
If a disc is damaged, dirty, or loaded upside down, the
disc will be skipped and the next disc will automatically
play.
Display
Click on the first or last page to see other CD-DP2500 (serv.man2) service manuals if exist.
Random: