Read Panasonic FZ-A1BDAAXXM / FZ-A1BDAAEE9 / FZ-A1BDAAZE9 Service Manual online
■ Processing of various kinds cables
*Notice
<Screw tightening torque>
Screw<N2> = 0.165 ± 0.01N·m (1.65 ± 0.1kgf·cm)
<Screw tightening order>
Screw<N2> = 1 - 2
<Screw tightening torque>
Screw<N2> = 0.165 ± 0.01N·m (1.65 ± 0.1kgf·cm)
<Screw tightening order>
Screw<N2> = 1 - 2
Note: 1. Insert the black cable using gauges, and then settle the
black antenna to the edge of the WWAN clip, as shown
in the figure.
2. For 3 connecters, connecters at both sides can be used.
in the figure.
2. For 3 connecters, connecters at both sides can be used.
Charger Holder
Screw<N2>
Screw<N2>
WWAN model
Non-WWAN model
1
2
1. Take the Charger Holder to position on the Docking BD,
and then tighten screws*2.
and then tighten screws*2.
2. Settle the LTE AUX Antenna within the slot, and paste 1pcs mylar
at place as shown in the figure.
at place as shown in the figure.
3.
(WWAN model)
Take off the protecting jacket from antennas,
and then insert the LTE AUX Antenna and LTE Main Antenna
into WWAN.
into WWAN.
(Non-WWAN model)
Retain the protecting jacket, and paste
the antenna at the bottom of the Lower Case / Speaker Ass'y
using the black Tape, as shown in the figure.
using the black Tape, as shown in the figure.
Paste half of the mylar
on the protecting jacket
and half on the calbe to
be fixed.
on the protecting jacket
and half on the calbe to
be fixed.
The cable bypasses upper the positioning pin
and is fixed as shown in the figure.
and is fixed as shown in the figure.
The cable goes through this slot.
LTE AUX Antenna
LTE Main Antenna
Implement pasting
completely.
completely.
Settle cables under
the sheetmetal.
the sheetmetal.
1. Make the SPK metal pin upwards to insert into the Main PCB
connecter.
connecter.
Note: Make the metal Pin upwards.
2. Insert the excess portion of the speaker cable to the groove
position.
Cable under the connecter edge using the black Tape, and then
paste half of a piece of Tape at the corner of the Lower Case /
Speaker Ass'y.
position.
Cable under the connecter edge using the black Tape, and then
paste half of a piece of Tape at the corner of the Lower Case /
Speaker Ass'y.
4. Take off the protecting jacket from the GPS connecter, and
insert the GPS connecter into the Main PCB interface.
5. Wiring of the GPS cable to the edge of the aluminum and
magnesium parts, fix the GPS Cable at the position using
1pcs mylar, as shown in the figure.
insert the GPS connecter into the Main PCB interface.
5. Wiring of the GPS cable to the edge of the aluminum and
magnesium parts, fix the GPS Cable at the position using
1pcs mylar, as shown in the figure.
Note:
3. Position the GPS in the slot in
the right corner of the Lower
Case / Speaker Ass'y as shown
in the figure.
the right corner of the Lower
Case / Speaker Ass'y as shown
in the figure.
Check whether the cable is
settled well before pasting.
settled well before pasting.
Perform the
positioning
downwards
the connecter.
positioning
downwards
the connecter.
Perform half stick with
covering the white label
using the Tape.
covering the white label
using the Tape.
Put the foam
side toward
the right.
side toward
the right.
The left side of the Tape covers
the pane, but do not cover BD.
the pane, but do not cover BD.
7-9
Click on the first or last page to see other FZ-A1BDAAXXM / FZ-A1BDAAEE9 / FZ-A1BDAAZE9 service manuals if exist.