Read Panasonic KV-S5055C (serv.man2) Service Manual online
113
6. Double Feed Detector (R) does
not work, properly.
not work, properly.
1. Execute Double Feed test in Sec.9.3.6 to
check the detector condition.
2. Check whether the Double Feed
Detector (R) is aligned property.
3. Check the following connection and
soldering condition on each connector.
check the detector condition.
2. Check whether the Double Feed
Detector (R) is aligned property.
3. Check the following connection and
soldering condition on each connector.
a. CN2010 (USR SENSOR Board) to
CN2005 (USS RELAY Board)
b. CN2001 (USS RELAY Board)
to CN1007 (CONTROL Board)
4. Check the following parts' soldering
condition to repair it.
b. CN2001 (USS RELAY Board)
to CN1007 (CONTROL Board)
4. Check the following parts' soldering
condition to repair it.
a. CONTROL Board
IC0006 - 98th pin
b. USS RELAY board
All parts.
All parts.
5. Check the following signals on the USS
RELAY Board.
RELAY Board.
a. DC 12 V signal (CN2001-7th pin)
b. DC 5 V signal (CN2001-6th pin)
b. DC 5 V signal (CN2001-6th pin)
6. Replace faulty parts or boards.
U25 (Detect document
with staples
(Double-feed detec-
tion)
with staples
(Double-feed detec-
tion)
1E
00
00
00 1. Refer to each item on classified code U23.
U26 (Detect document
with staples (Bent-
paper detection)
with staples (Bent-
paper detection)
1F
xx
00
00 1. Bent Paper was detected.
1. Check whether the scanned documents are
fixed by staples or others.
2. Set the documents on the Hopper orderly,
and then scan them again.
fixed by staples or others.
2. Set the documents on the Hopper orderly,
and then scan them again.
2. Some of Bent Paper Sensors do
not work, properly.
not work, properly.
1. Execute Key/Sensor test in Sec. 9.3.6 to
check Bent Paper Sensors' condition while
covering the sensors with white paper.
2. Check whether the BENT PAPER SENSOR
S (L) Board, BENT PAPER SENSOR R (L)
Board, BENT PAPER SENSOR S (R) Board
and BENT PAPER SENSOR R (R) Board
are aligned properly.
3. Check the following connection and
soldering condition on each connector,
check Bent Paper Sensors' condition while
covering the sensors with white paper.
2. Check whether the BENT PAPER SENSOR
S (L) Board, BENT PAPER SENSOR R (L)
Board, BENT PAPER SENSOR S (R) Board
and BENT PAPER SENSOR R (R) Board
are aligned properly.
3. Check the following connection and
soldering condition on each connector,
a. CN2007 (USS RELAY Board) to CN3005
(BENT RELAY Board)
b. CN3006 (BENT RELAY Board) to CN3010
(BENT PAPER SENSOR R (L) Board)
c. CN3011 (BENT PAPER SENSOR R (L)
Board) to CN3014 (BENT PAPER
SENSOR S (L) Board)
d. CN3007(BENT RELAY Board) to CN3012
(BENT PAPER SENSOR R(R) Board)
e. CN3013(BENT PAPER SENSOR R(R)
Board) to CN3015(BENT PAPER
SENSOR S (R) Board)
(BENT RELAY Board)
b. CN3006 (BENT RELAY Board) to CN3010
(BENT PAPER SENSOR R (L) Board)
c. CN3011 (BENT PAPER SENSOR R (L)
Board) to CN3014 (BENT PAPER
SENSOR S (L) Board)
d. CN3007(BENT RELAY Board) to CN3012
(BENT PAPER SENSOR R(R) Board)
e. CN3013(BENT PAPER SENSOR R(R)
Board) to CN3015(BENT PAPER
SENSOR S (R) Board)
4. Check the following parts’ soldering
condition to repair it.
a. CONTROL Board
condition to repair it.
a. CONTROL Board
IC0015 (21, 23, 24, and 27th pins)
b. USS RELAY Board
IC2008 (3, 15, 18, 20, 22, 24, and
b. USS RELAY Board
IC2008 (3, 15, 18, 20, 22, 24, and
27th pins)
IC2001 to IC2003, IC2005, IC2006, Q2009
to Q2014, and their surrounding circuit.
5. Check the following signals
5. Check the following signals
a. DC14 V signal (CN2006-3rd pin and
CN2007-1st pin)
b. BPS_D_L (CN3014-3rd pin) and
CN2007-1st pin)
b. BPS_D_L (CN3014-3rd pin) and
BPS_D_R (CN3015-3rd pin)
→ See Fig. 11.
6. Replace faulty parts or boards.
U30 (ADF Door or
Imprinter Door is
open.)
Imprinter Door is
open.)
20
00
00
00 1. ADF Door or Imprinter Door is
not closed enough.
Shut the door properly.
Error Code
Possible Cause
Check Point
Remarks
Classified Code ST1 ST2 ST3 ST4
Click on the first or last page to see other KV-S5055C (serv.man2) service manuals if exist.