Read Panasonic KV-S5055C (serv.man2) Service Manual online
111
3. Exit Sensor does not work,
correctly
correctly
1. Execute Key/Sensor test in the Sec. 9.3.6 to
check the sensor condition.
2. Check the sensor alignment is proper
(whether the sensor direction faces to its
reflector.)
3. Check the following connection and
soldering condition on each connector.
check the sensor condition.
2. Check the sensor alignment is proper
(whether the sensor direction faces to its
reflector.)
3. Check the following connection and
soldering condition on each connector.
a. CN3003 (ENDING SENSOR Board)
to CN2004 (USR RELAY Board)
b. CN2001 (USR RELAY Board)
to CN1007 (CONTROL Board)
4. Check the following signals.
4. Check the following signals.
a. ENDING signal (CN2004-1st or
CN1007-4th pin)
CN1007-4th pin)
→ 0 V (when none exists on the
Exit Sensor)
b. Check the reference signal for the
ENDING signal on the CONTROL Board.
IC0023-5th pin: 1.5 V or less
IC0025-6th pin: Approx. 1.5 V
c. Check comparator output signal.
ENDING signal on the CONTROL Board.
IC0023-5th pin: 1.5 V or less
IC0025-6th pin: Approx. 1.5 V
c. Check comparator output signal.
→ IC0017-6th pin: 3.3 V (when no
document exists)
5. Replace faulty parts or cables.
5. Replace faulty parts or cables.
4. Mechanical problem (Drive
Rollers, Drive Belt, Conveyor)
Rollers, Drive Belt, Conveyor)
1. Execute Conveyor Motor test in Sec.9.3.6
to check the mechanical condition.
2. Check whether the Drive Rollers (2, 3),
Drive Belt, and the conveyor to support
the Drive Rollers are put together into
the scanner, properly.
3. Check the surfaces of the Drive Rollers
(2, 3).
a. Configuration:
to check the mechanical condition.
2. Check whether the Drive Rollers (2, 3),
Drive Belt, and the conveyor to support
the Drive Rollers are put together into
the scanner, properly.
3. Check the surfaces of the Drive Rollers
(2, 3).
a. Configuration:
Do the rollers swell irregularly?
→ Replace the rollers.
b. Whether the roller surfaces are dirty
→ Clean the surfaces.
4. Check whether the Drive Belt tension is
proper.
proper.
U16 (Exit Jam1: Paper
did not pass through
the Exit Sensor)
did not pass through
the Exit Sensor)
16
00
00
00 1. Document remains forward
Exit Sensor.
Remove the document from the scanner.
2. Paper dust exists on or around
the Exit Sensor.
the Exit Sensor.
1. Blow off the dirt with the accessory blower.
(See Sec.7.2.)
2. Execute Key/Sensor and Sensor Sensitive
Level tests in Sec. 9.3.6 to check the sensor
condition.
(See Sec.7.2.)
2. Execute Key/Sensor and Sensor Sensitive
Level tests in Sec. 9.3.6 to check the sensor
condition.
3. Mechanical problem (Exit Roller,
Drive Belt, Conveyor)
Drive Belt, Conveyor)
1. Execute Conveyor Motor test in Sec.9.3.6
to check the mechanical condition.
2. Check whether the Drive Roller (3), Exit
Roller, Drive Belt, and the conveyor to
support the rollers are put together into the
scanner, properly.
3. Check the surfaces of the Drive Roller (3)
and the Exit Roller.
a. Configuration:
to check the mechanical condition.
2. Check whether the Drive Roller (3), Exit
Roller, Drive Belt, and the conveyor to
support the rollers are put together into the
scanner, properly.
3. Check the surfaces of the Drive Roller (3)
and the Exit Roller.
a. Configuration:
Do the rollers swell irregularly?
→ Replace the rollers.
b. Whether the roller surfaces are dirty
→Clean the surfaces.
4. Check whether the Drive Belt tension is
proper.
proper.
→ Re-adjust the belt tension.
U18 (Paper remains in
the scanner)
the scanner)
18
xx
00
00 1. Document remains in scanner.
Remove the document from the scanner.
2. Paper dust exists on a sensor.
1. Execute Key/Sensor and Sensor Sensitive
Level tests in Sec. 9.3.6 to define the sensor
that results in this problem.
2. Blow off the dirt on the surface of the sensor
with the accessory blower. (See Sec.7.2.)
Level tests in Sec. 9.3.6 to define the sensor
that results in this problem.
2. Blow off the dirt on the surface of the sensor
with the accessory blower. (See Sec.7.2.)
Error Code
Possible Cause
Check Point
Remarks
Classified Code ST1 ST2 ST3 ST4
Click on the first or last page to see other KV-S5055C (serv.man2) service manuals if exist.