Read Panasonic KV-S4065CL / KV-S4065CW / KV-S4085CL / KV-S4085CW Service Manual Supplement online
16
5 "SECTION 10 TROUBLESHOOTING"
5.1.
“Section 10.3 Requirement After Parts Replacement”
Replaced circuit board assembly or part
Adjustment to be required
Remarks
IC1011 (Flash Memory on CONTROL Board)
1. Adjust “Shading”.
IC1008 (EEPROM on CONTROL Board) or CONTROL
Board
Board
1. Adjust “Shading”.
2. Adjust “All Position”.
3. Execute “Double Feed” (See 9.3.7) to adjust double
feed sensitivity.
4. Execute "Bent Paper Sensor" in Sec. 9.3.7 to
adjust the sensor level.
5. Set USB ID. (See 9.3.7.)
2. Adjust “All Position”.
3. Execute “Double Feed” (See 9.3.7) to adjust double
feed sensitivity.
4. Execute "Bent Paper Sensor" in Sec. 9.3.7 to
adjust the sensor level.
5. Set USB ID. (See 9.3.7.)
6. In Sleep Mode, set the “Standby” condition
to “30 min.” (For KV-S4065CL-U/ S4065CW-
U/ S4085CL-U/ S4085CW-U Only)
to “30 min.” (For KV-S4065CL-U/ S4065CW-
U/ S4085CL-U/ S4085CW-U Only)
Starting Sensor or STARTING SENSOR Board
1. Adjust Vertical Position (for Front and Back) and
Length in “Individual Position” or adjust
“All Position”.
Length in “Individual Position” or adjust
“All Position”.
DOUBLE FEED DETECTOR LCR Board
1. Execute “Double Feed” (See 9.3.7.) to adjust double
feed sensitivity.
feed sensitivity.
DOUBLE FEED DETECTOR L Board
1. Execute “Double Feed” (See 9.3.7.) to adjust double
feed sensitivity.
feed sensitivity.
DOUBLE FEED DETECTOR C Board
1. Execute “Double Feed” (See 9.3.7.) to adjust double
feed sensitivity.
feed sensitivity.
DOUBLE FEED DETECTOR R Board
1. Execute “Double Feed” (See 9.3.7.) to adjust double
feed sensitivity.
feed sensitivity.
CIS (F)
1. Adjust “Shading”.
2. Adjust “All Position” or the following adjustment
should be needed.
a. Adjust Front Vertical Position in “Individual
Position”.
b. Adjust Front Horizontal Position in “Individual
Position”.
2. Adjust “All Position” or the following adjustment
should be needed.
a. Adjust Front Vertical Position in “Individual
Position”.
b. Adjust Front Horizontal Position in “Individual
Position”.
CIS (B)
1. Adjust “Shading”.
2. Adjust “All Position” or the following adjustment
should be needed.
a. Adjust Back Vertical Position in “Individual
Position”.
b. Adjust Back Horizontal Position in “Individual
Position”.
2. Adjust “All Position” or the following adjustment
should be needed.
a. Adjust Back Vertical Position in “Individual
Position”.
b. Adjust Back Horizontal Position in “Individual
Position”.
Reference Plate (F)
1. Adjust “Shading”.
Reference Plate (B)
1. Adjust “Shading”.
Drive Roller
1. Adjust Vertical Position (for Front and Back) and
Length in “Individual Position” or adjust “All
Position”.
Length in “Individual Position” or adjust “All
Position”.
Exit Roller
1. Adjust Vertical Position (for Front and Back) and
Length in “Individual Position” or adjust “All
Position”.
Length in “Individual Position” or adjust “All
Position”.
Others (when assembling or disassembling parts
(Conveyor etc.) which will affect the scanning positions.)
(Conveyor etc.) which will affect the scanning positions.)
1. Perform the following adjustment or “All Position”.
a. Adjust Front Vertical Position in “Individual
Position”.
b. Adjust Front Horizontal Position in “Individual
Position”.
c. Adjust Back Vertical Position in “Individual
Position”.
d. Adjust Back Horizontal Position in “Individual
Position”.
a. Adjust Front Vertical Position in “Individual
Position”.
b. Adjust Front Horizontal Position in “Individual
Position”.
c. Adjust Back Vertical Position in “Individual
Position”.
d. Adjust Back Horizontal Position in “Individual
Position”.
Roller Holder Unit, Hopper Arm
1. Execute “Roller Pressure Sensor Level” to confirm
the pressure level (See 9.3.6.).
the pressure level (See 9.3.6.).
Click on the first or last page to see other KV-S4065CL / KV-S4065CW / KV-S4085CL / KV-S4085CW service manuals if exist.