Read Panasonic PT-RZ670 / PT-RW630 (serv.man5) Other Service Manuals online
1. The name of each part ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
INF-2
1. 1. Projector body
1. 2. Control panel
1. 3. Connecting terminals
1. 4. Remote control
1. 2. Control panel
1. 3. Connecting terminals
1. 4. Remote control
2. OSD Menu Navigation ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
INF-5
3. Service Mode ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
INF-9
3. 1. Setting to Service Mode
3. 2. Resetting to User Mode
3. 3. Functions in Service Mode
3. 2. Resetting to User Mode
3. 3. Functions in Service Mode
4. External control ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
INF-14
4. 1. Control through Serial terminal
4. 2. Control through LAN terminal
4. 3. Control commands List
4. 2. Control through LAN terminal
4. 3. Control commands List
5. Notification for service operation ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
INF-20
5. 1. Before service operation
5. 2 Service
5. 3. Replacement of consumable parts
5. 4. Initialization for control device password
5. 2 Service
5. 3. Replacement of consumable parts
5. 4. Initialization for control device password
6 Troubleshooting ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
INF-23
6. 1. Shutdown system
CONTENTS
SECTION 1
SERVICE INFORMATION
Model No.
PT-RZ670
PT-RW630
PT-RW630
SECTION 1 SERVICE INFORMATION
< RZ670/RW630 >
1. The name of each part
1. 1. Projector body
1
2
3
4
5
6
7
7
10
8
8
11
9
16
17
14
13
15
7
7
7
Front
Side
Rear
8
8
8
12
Projection direction
Bottom
1 Remote control signal receiver (front)
2 Power indicator <ON (G)/STANDBY (R)>
Displays the status of the power.
3 Light source indicator <LIGHT1>
Displays the status of light source 1.
4 Light source indicator <LIGHT2>
Displays the status of light source 2.
5 Temperature indicator <TEMP>
Displays the internal temperature status.
6 (Not available with this projector)
7 Adjustable
feet
Adjusts the projection angle.
8 Air intake port
9 Projection
lens
(Only models with lens)
10 Remote control signal receiver (rear)
11 Air exhaust port
12 Burglar hook port
Attaches a burglar prevention cable, etc.
13 Control
panel
14 Connecting
terminals
15 Security
slot
This security slot is compatible with the Kensington security
cables.
cables.
16 <MAIN POWER> switch
Turns on/off the main power.
17 <AC IN> terminal
Connect the supplied power cord.
Attention
f Do not block the ventilation ports (intake and exhaust) of the projector.
INF - 2
SECTION 1 SERVICE INFORMATION
< RZ670/RW630 >
1. 2. Control panel
1. 3. Connecting terminals
9
10
11
12
13
14
2
4
3
1
5
6
7
8
1 Power on <
b> button
Starts projection when the <MAIN POWER> switch on the
projector is set to <ON> when the power is switched off
(standby mode).
projector is set to <ON> when the power is switched off
(standby mode).
2 Power standby <
v> button
Sets the projector to the state where the projector is switched
off (standby mode) when the <MAIN POWER> switch on the
projector is set to <ON> and in projection mode.
off (standby mode) when the <MAIN POWER> switch on the
projector is set to <ON> and in projection mode.
3 <RGB1>
button
Switches the input to RGB1.
4 <RGB2>
button
Switches the input to RGB2.
5 <DVI-D>
button
Switches the input to DVI-D.
6 <HDMI>
button
Switches the input to HDMI.
7 <DIGITAL LINK> button
Switches the input to DIGITAL LINK.
8 <SDI>
button
Switches the input to SDI.
(Only for PT-RZ670)
(Only for PT-RZ670)
9 <MENU>
button
Displays or hides the main menu.
Returns to the previous menu when a sub-menu is displayed.
If you press the <MENU> button on the control panel for at least
three seconds while the on-screen display is off (hidden), the
on-screen display is turned on.
If you press the <MENU> button on the control panel for at least
three seconds while the on-screen display is off (hidden), the
on-screen display is turned on.
10 <LENS>
button
Adjusts the focus, zoom, and shift (position) of the lens.
11 <ENTER>
button
Determines and executes an item in the menu screen.
12 <SHUTTER>
button
Used to temporarily turn off the image.
13
asqw buttons
Used to select items in the menu screen, change settings, and
adjust levels.
Also used to enter a password in [SECURITY] or enter
characters.
Used to select items in the menu screen, change settings, and
adjust levels.
Also used to enter a password in [SECURITY] or enter
characters.
14 <AUTO SETUP> button
Automatically adjusts the image display position while projecting
the image. [PROGRESS] is displayed while in automatic
adjustment.
the image. [PROGRESS] is displayed while in automatic
adjustment.
1
2
3
4
5
6
7
8
9
10
1 <REMOTE 1 IN> terminal/<REMOTE 1 OUT> terminal
These are the terminals to connect the remote control for serial
control in a multiple projector environment.
control in a multiple projector environment.
2 <REMOTE 2 IN> terminal
This is a terminal to remotely control the projector using the
external control circuit.
external control circuit.
3 <SERIAL IN> terminal
This is the RS-232C compatible terminal to externally control
the projector by connecting a computer.
the projector by connecting a computer.
4 <SERIAL OUT> terminal
This is a terminal to output the signal connected to the <SERIAL
IN> terminal.
IN> terminal.
5 <SDI IN> terminal
This is the terminal to input SDI signals.
(Only for PT-RZ670)
(Only for PT-RZ670)
6 <RGB 1 IN> (<R/P
R
/VIDEO>, <G/Y>, <B/P
B
/C>, <SYNC/HD>,
<VD>) terminals
These are terminals to input RGB signals, YC
These are terminals to input RGB signals, YC
B
C
R
/YP
B
P
R
signals, Y/C signals, or video signals.
7 <RGB 2 IN> terminal
This is a terminal to input RGB signals or YC
B
C
R
/YP
B
P
R
signals.
8 <DVI-D IN> terminal
This is the terminal to input DVI-D signals.
9 <HDMI IN> terminal
This is the terminal to input HDMI signals.
10 <DIGITAL LINK/LAN> terminal
This is the LAN terminal to connect to the network. This is also
used when connecting a video signal transmission device via
the LAN terminal.
used when connecting a video signal transmission device via
the LAN terminal.
Attention
f When a LAN cable is directly connected to the projector, the network connection must be made indoors.
INF - 3
SECTION 1 SERVICE INFORMATION
< RZ670/RW630 >
1. 4. Remote control
1
3
2
4
5
7
6
8
9
10
15
12
11
13
14
14
16
17
Front
Top
Bottom
1 Power standby <
v> button
Sets the projector to the state where the projector is switched
off (standby mode) when the <MAIN POWER> switch on the
projector is set to <ON> and in projection mode.
off (standby mode) when the <MAIN POWER> switch on the
projector is set to <ON> and in projection mode.
2 Power on <
b> button
Starts projection when the <MAIN POWER> switch on the
projector is set to <ON> when the power is switched off
(standby mode).
projector is set to <ON> when the power is switched off
(standby mode).
3 Remote control indicator
Blinks if any button in the remote control is pressed.
4 Lens (<FOCUS>, <ZOOM>, <SHIFT>) buttons
Adjusts the projection lens.
5 <MENU> button/<ENTER> button/
asqw buttons
Used to navigate through the menu screen.
6 <ON SCREEN> button
Switches the on-screen display function on (display) or off
(hide).
(hide).
7 Input selection (<RGB1/2>, <DIGITAL LINK>, <DVI-D>,
<VIDEO>, <SDI>, <HDMI>) buttons
Switches the input signal to project.
Switches the input signal to project.
(SDI input is supported only for PT-RZ670.)
8 <FUNCTION>
button
Assigns a frequently used operation as a shortcut button.
9 Number (<0> - <9>) buttons
Used for entering an ID number or a password in a multiple
projector environment.
projector environment.
10 <AUTO SETUP> button
Automatically adjusts the image display position while projecting
the image.
[PROGRESS] is displayed while in automatic adjustment.
the image.
[PROGRESS] is displayed while in automatic adjustment.
11 <SHUTTER>
button
Used to temporarily turn off the image.
12 <TEST PATTERN> button
Displays the test pattern.
13 <STATUS>
button
Displays the projector information.
14 <DEFAULT>
button
Resets the content of the sub-menu to the factory default.
15 <ID SET> button
Sets the ID number of the remote control in a multiple projector
environment.
environment.
16 Remote control signal transmitter
17 Remote control wired terminal
This is the terminal used to connect to the projector via a cable
when used as a wired remote control.
when used as a wired remote control.
Attention
f Do not drop the remote control.
f Avoid contact with liquids or moisture.
f Do not attempt to modify or disassemble the remote control.
Note
f When operating the remote control by directly pointing at the remote control signal receiver of the projector body, operate the remote
control within a distance approx. 30 m (98'5") from the remote control signal receiver. The remote control can control at angles of up to ±30°
vertically and horizontally, but the effective control range may be reduced.
vertically and horizontally, but the effective control range may be reduced.
f If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not operate properly.
f
f
. Use
it in a place distant from the light source.
f The power indicator <ON (G)/STANDBY (R)> will blink if the projector receives a remote control signal.
f The operation of the <VIDEO> button is disabled in the factory default settings. The operation is enabled when [REMOTE CONTROL] is set
to [USER] and [VIDEO BUTTON] of [INPUT SELECT BUTTON] is set to other than [DISABLE], from the [SECURITY] menu
→ [CONTROL
DEVICE SETUP]
INF - 4