Read Panasonic UF-6300 / UF-6200 / UF-5300 Service Manual online
122
570
RCV
B
Password or machine code did not
match during remote diagnostic
communication.
match during remote diagnostic
communication.
571
XMT
B
Remote unit did not have the
remote diagnostic function.
remote diagnostic function.
580
XMT
B
Sub-address transmission to a unit
that has their DIS bit 49 (NSF bit
155) OFF.
that has their DIS bit 49 (NSF bit
155) OFF.
Sub-address transmission to a unit that
has no Sub-address function.
has no Sub-address function.
581
XMT
B
Sub-address Password
transmission to a unit that has their
DIS bit 50 (NSF bit 156) OFF.
transmission to a unit that has their
DIS bit 50 (NSF bit 156) OFF.
Sub-address transmission to a unit that
has no Sub-address function.
has no Sub-address function.
601
XMT
ADF Door was opened during ADF
transmission.
transmission.
623
XMT
A
No original was in the ADF. (Built-in
dialer engaged)
dialer engaged)
Operator removed the original from the
ADF after dialing was completed.
Original was not set properly in the
ADF.
ADF after dialing was completed.
Original was not set properly in the
ADF.
630
XMT or
RCV
(Polling)
B
Redial count over.
No dial tone detected. Sensor dial tone
is not detected. (destination dependent)
Busy tone is detected. (destination
dependent) T1 timer (35±5 sec.)
elapsed without a signal from the
receiver.
is not detected. (destination dependent)
Busy tone is detected. (destination
dependent) T1 timer (35±5 sec.)
elapsed without a signal from the
receiver.
631
XMT
A
"STOP" button was pressed during
Auto Dialing.
Auto Dialing.
634
XMT
B
Redial count over with no response
or busy tone was not detected.
or busy tone was not detected.
Note:
U.S.A. and Canadian models
will redial only once if a busy
tone is not detected.
will redial only once if a busy
tone is not detected.
Telephone line cable is disconnected.
Wrong number is dialed.
SC or MJR PCB is abnormal.
Wrong number is dialed.
SC or MJR PCB is abnormal.
638
XMT
LAN
Power turned off with applicable
data in memory or during
communication.
data in memory or during
communication.
Power cord unplugged. Power failure
occurred.
occurred.
711
RCV
LAN
Incorrect LDAP settings.
LDAP Server Name, LDAP Login
Name, LDAP Password and/or LDAP
Search Base are incorrect.
Name, LDAP Password and/or LDAP
Search Base are incorrect.
712
XMT
LAN
Unknown email address replied
from the Mail Server.
from the Mail Server.
Mail Server received an incorrect email
address. (Dependent on Server's Mail
application)
address. (Dependent on Server's Mail
application)
714
XMT
RCV
RCV
LAN
LAN Interface error.
Cannot logon to the LAN.
Cannot logon to the LAN.
The 10Base-T/100Base-TX cable is not
connected.
An unexpected LAN problem occurred.
Check the LANC/LANB PCB connector.
connected.
An unexpected LAN problem occurred.
Check the LANC/LANB PCB connector.
715
XMT
LAN
TCP/IP connection timed out.
Incorrect IP Address is set.
Verify the IP Address, Default Router IP
Address, SMTP Server IP Address.
Verify the IP Address, Default Router IP
Address, SMTP Server IP Address.
716
XMT
LAN
Cannot logon to the LAN.
Incorrect SMTP Server IP Address is
set.
No email application is activated on the
Mail Server.
set.
No email application is activated on the
Mail Server.
717
XMT
LAN
Incomplete SMTP Protocol
transmission.
transmission.
Mail Server’s hard disk may be full.
Mail Server is defective.
Mail Server is defective.
Fax Information Codes
Code
Mode
Phase
Description of Problem
Cause
Click on the first or last page to see other UF-6300 / UF-6200 / UF-5300 service manuals if exist.