Read Panasonic UF-6300 / UF-6200 / UF-5300 Service Manual online
120
409
XMT
D
Transmitter receives PIN after it
transmitted a post message, such
as EOP, MPS, EOM, etc.
transmitted a post message, such
as EOP, MPS, EOM, etc.
Receiver receives data with error due to
poor line quality, and receiving operator
requests voice contact.
Receiver is defective. (Modem, etc.)
SC PCB or MJR PCB are defective.
poor line quality, and receiving operator
requests voice contact.
Receiver is defective. (Modem, etc.)
SC PCB or MJR PCB are defective.
410
RCV
D
Received DCN while waiting for
post command. (EOP, MPS, EOM,
etc.)
post command. (EOP, MPS, EOM,
etc.)
Interface or line is faulty.
Transmitter is defective.
Transmitter is defective.
411
RCV
(Polling)
B
Received DCN after transmitting
NSC.
NSC.
Transmitter is not ready for polling
communication.
Password does not match between
transmitter and receiver.
communication.
Password does not match between
transmitter and receiver.
412
G3 RX
B, D
No response within 12 seconds in
NSS/DCS/MPS wait state. (After
transmitting FTT)
NSS/DCS/MPS wait state. (After
transmitting FTT)
Transmitter is defective.
SC PCB is defective.
SC PCB is defective.
414
RCV
(Polling)
B
No response received after
transmitting 3rd NSC.
transmitting 3rd NSC.
Password does not match between
transmitter and receiver.
Transmitter is defective. (No original,
document jam, etc.)
transmitter and receiver.
Transmitter is defective. (No original,
document jam, etc.)
415
XMT
(Polling)
B
Remote side attempted to receive
message from your machine in
polling communication.
message from your machine in
polling communication.
Inform the remote side that your
machine does not have the polling
transmission feature.
machine does not have the polling
transmission feature.
416
RCV
D
Receiver did not detect post
command, such as EOP, MPS,
EOM, etc.
command, such as EOP, MPS,
EOM, etc.
Transmitter is defective.
Line quality is poor. (RTC signal is
distorted due to line noise)
SC PCB or MJR PCB are defective.
Line quality is poor. (RTC signal is
distorted due to line noise)
SC PCB or MJR PCB are defective.
417
RCV
C
Receiver returned RTN in response
to post message.
to post message.
Line quality is poor. (There are
excessive errors in received data)
SC PCB or MJR PCB are defective.
excessive errors in received data)
SC PCB or MJR PCB are defective.
418
RCV
C
Receiver transmitted PIN in
response to PRI-Q from transmitter.
(Transmitting operator requests
voice contact)
response to PRI-Q from transmitter.
(Transmitting operator requests
voice contact)
Line quality is poor. (There are
excessive errors in received data)
SC PCB or MJR PCB are defective.
excessive errors in received data)
SC PCB or MJR PCB are defective.
420
RCV
B
T1 timer (35 sec.) elapsed without
detecting 300 bps signal.
detecting 300 bps signal.
There is wrong incoming call.
(non-facsimile communication)
Transmitter is defective.
SC PCB or MJR PCB are defective.
(non-facsimile communication)
Transmitter is defective.
SC PCB or MJR PCB are defective.
421
RCV
B
Busy Tone is detected after sending
NSF Signal.
NSF Signal.
Remote station disconnected the line.
Wrong number is dialed.
Wrong number is dialed.
422
XMT
B
Content of NSF (or DIS) or NSC (or
DTC) was invalid.
DTC) was invalid.
There is an incompatibility.
427
G3
RCV
B
DCN received to NSF/CSI/DIS
transmitted.
transmitted.
The interface is incompatible.
433
XMT
RCV
RCV
B, D
T.30 Protocol abnormal.
Defective remote station.
434
XMT or
RCV
B
CD (response from Modem) did not
turn OFF within 180 sec. after
receiver detected FLAG signal.
turn OFF within 180 sec. after
receiver detected FLAG signal.
Remote unit is defective.
SC PCB or MJR PCB are defective.
SC PCB or MJR PCB are defective.
436
G3 RX
C
DCN received after transmitting
FTT.
FTT.
Transmitter is defective or incompatible.
Line quality is poor.
Line quality is poor.
Fax Information Codes
Code
Mode
Phase
Description of Problem
Cause
Click on the first or last page to see other UF-6300 / UF-6200 / UF-5300 service manuals if exist.