Read Panasonic UF-6300 / UF-6200 / UF-5300 Service Manual online
121
438
RCV
B
Refusal ID (Junk Fax ID) received
in Phase B.
in Phase B.
Transmitter ID is registered as a Junk
Fax. JUNK is printed as the Information
Code on the Comm. Journal.
Fax. JUNK is printed as the Information
Code on the Comm. Journal.
456
RCV
B
Received relay transfer request or
confidential document to distribute
to an end receiving station or all
confidential mailboxes are used.
confidential document to distribute
to an end receiving station or all
confidential mailboxes are used.
459
RCV
C
Failed training in Phase C.
Line quality is poor. (Training signal is
distorted due to line noise)
SC PCB or MJR PCB are defective.
distorted due to line noise)
SC PCB or MJR PCB are defective.
490
RCV
C
Sum of error lines exceeded the
limit (Function Parameter No. 70) of
64 lines.
limit (Function Parameter No. 70) of
64 lines.
Line quality is poor.
SC PCB or MJR PCB are defective.
SC PCB or MJR PCB are defective.
494
RCV
C
Interval between two EOLs was
more than 10 sec. when receiver
received message data.
more than 10 sec. when receiver
received message data.
Transmitter is defective.
Line quality is poor. (EOL is damaged
due to line noise)
SC PCB or MJR PCB are defective.
Line quality is poor. (EOL is damaged
due to line noise)
SC PCB or MJR PCB are defective.
495
XMT
RCV
RCV
C
During reception, CD turned OFF
or continued ON for long time.
During communication, lost loop -
current.
or continued ON for long time.
During communication, lost loop -
current.
Line is disconnected.
Transmitter is defective.
SC PCB or MJR PCB are defective.
Transmitter is defective.
SC PCB or MJR PCB are defective.
496
XMT
C
CS of modem is not able to turn
ON.
ON.
SC PCB is defective.
501
XMT/
RCV(V.34)
B
Remote unit does not have
compatible Modem.
compatible Modem.
502
XMT/
RCV(V.34)
B, C, D During reception, CD turned OFF
or continued ON for long time.
During communication, lost loop -
current.
During communication, lost loop -
current.
Line is disconnected.
Transmitter is defective.
SC PCB or MJR PCB are defective.
Transmitter is defective.
SC PCB or MJR PCB are defective.
503
XMT/
RCV(V.34)
B, C, D CS of modem is not able to turn ON
during training.
SC PCB is defective.
Line is disconnected.
Line is disconnected.
504
XMT/V.34
(Polling)
B
Polling is rejected from the remote
station.
station.
No polling original is set.
505
XMT/V.34
(Polling)
B
Polling XMT is rejected.
No polling original is set.
540
XMT ECM
B
No response after transmitting 3rd
CTC or DCN received.
CTC or DCN received.
Incompatible interface.
541
XMT ECM
D
No response after transmitting 3rd
EOR or received DCN.
EOR or received DCN.
Line is faulty.
MJR PCB abnormal.
MJR PCB abnormal.
542
XMT ECM
D
No response to the 3rd RR
transmitted or received DCN.
transmitted or received DCN.
Remote unit is abnormal.
543
XMT ECM
D
T5 timer (60 sec.) elapsed without
MCF.
MCF.
Remote unit is abnormal.
544
XMT ECM
D
Stopped Transmission after EOR
Transmission.
Transmission.
Line is faulty.
MJR PCB abnormal.
MJR PCB abnormal.
550
RCV ECM
C
Timer between frames in phase C
has elapsed.
has elapsed.
Defective remote station.
554
RCV ECM
D
Transmitted ERR after receiving
EOR.
EOR.
Line is faulty.
555
RCV ECM
D
Transmitted PIN after receiving
EOR.
EOR.
Line is faulty and Operator Call
requested by RX side.
requested by RX side.
Fax Information Codes
Code
Mode
Phase
Description of Problem
Cause
Click on the first or last page to see other UF-6300 / UF-6200 / UF-5300 service manuals if exist.