Read Panasonic WV-CP240 Service Manual online
– 5 –
Fig. 5-3
3. Line Lock VCO Adjustment
(only for WV-CP240 and WV-CP244E)
Test Point:
TP1 (LL VCO)
Video Board
Adjust:
L1 (LL VCO)
Sensor Board
8
Remove the Sensor Board from the Front Unit while
referring to the item 3. Optical Ass'y Replacement
Procedure.
referring to the item 3. Optical Ass'y Replacement
Procedure.
8
Set the Synchronization Mode Selector (on the Video
Board SW1) to LL position.
Board SW1) to LL position.
8
Connect the Digital Voltmeter to TP1.
8
Adjust L1 so that the voltage becomes 1.65 V ± 0.35 V.
8
Return the Synchronization Mode Selector (on the Video
Board SW1) to INT position.
Board SW1) to INT position.
4. Flange-back Adjustment
Test Point:
CN5 (Video Output Connector)Video Board
Adjust:
Flange-back Adjusting Ring
8
Open the Lens Iris fully.
8
Set the Radiation Chart.
8
Aim the Camera at the Radiation Chart distance of 10m.
8
Referring to Fig. 5-3, loosen the Focus Fixing screw
(LOCK) that secure the Flange-back Adjusting Ring.
(LOCK) that secure the Flange-back Adjusting Ring.
Flange-back
Adjusting Ring
Adjusting Ring
Focus Fixing
Screw (LOCK)
Screw (LOCK)
LOC
K
8
Adjust the Flange-back Adjusting Ring to obtain best
focal point.
focal point.
8
Tighten the Focus fixing screw (LOCK) that secure the
Flange-back Adjusting Ring carefully.
Flange-back Adjusting Ring carefully.
8
Press the SAVE(F5) key of the Computer, then the
Computer will ask you for the file name.
Computer will ask you for the file name.
8
Type xxxxxxxx.EVR. Give an appropriate file name for
xxxxxxxx within 8 letters, but do not use CP240E.
xxxxxxxx within 8 letters, but do not use CP240E.
8
Press the ENTER key.
8
This saving procedure is recommended to keep the cur-
rent adjustment status of the Camera.
rent adjustment status of the Camera.
8
Press the LOAD(F1) key and type CP240E.EVR and
press the ENTER key for presetting adjustment of the
Camera.
press the ENTER key for presetting adjustment of the
Camera.
8
Press the ENTER key to start adjustment.
PANASONIC REMOTE EVR ADJUSTMENT SYSTEM (C) MCI Co. CCTV PRODUCT:CP240 EEPROM:0
✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽
MENU
✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽
Page (1/1)
✽ ✽ ✽ ✽ ✽
PAL
1. FSC ADJUSTMENT
3. ALC LEVEL
4. AGC OFF GAIN
5.1. OB LEVEL
5.2. VIDEO OUT GAIN
5.3. OB CONFIRM
6.1. BURST LEVEL
6.2. BURST LEVEL
6.3. BURST LEVEL
6.4. BURST LEVEL
7.1. 3200K R GAIN
7.2. 3200K B GAIN
7.3. 3200K PHASE
7.5. COLOUR CENTER POINT ADJUSTMENT
8.1. ATW CONFIRM
8.2. HI LIGHT CHROMA CLIP
<CONTENTS> TP2 [MAIN] 14.18750 MHz + - 40 Hz
<INSTRUCTION> PLEASE CHOOSE MENU DATA BY ARROW-KEY
3. ALC LEVEL
4. AGC OFF GAIN
5.1. OB LEVEL
5.2. VIDEO OUT GAIN
5.3. OB CONFIRM
6.1. BURST LEVEL
6.2. BURST LEVEL
6.3. BURST LEVEL
6.4. BURST LEVEL
7.1. 3200K R GAIN
7.2. 3200K B GAIN
7.3. 3200K PHASE
7.5. COLOUR CENTER POINT ADJUSTMENT
8.1. ATW CONFIRM
8.2. HI LIGHT CHROMA CLIP
<CONTENTS> TP2 [MAIN] 14.18750 MHz + - 40 Hz
<INSTRUCTION> PLEASE CHOOSE MENU DATA BY ARROW-KEY
LOAD (F1) QUIT (F3) SAVE (F5)
Table 5-1
<Adjustment Procedure-2 >
(E.V.R. Adjustment)
8
Insert new disk containing the E.V.R. Adjustment program
into IBM PC/AT and turn on the Power Switch of IBM
PC/AT.
into IBM PC/AT and turn on the Power Switch of IBM
PC/AT.
8
When starting an adjustment, at the prompt, type LADJ
CP240E and press the ENTER key, an initial menu will be
displayed in Table 5-1.
CP240E and press the ENTER key, an initial menu will be
displayed in Table 5-1.
Click on the first or last page to see other WV-CP240 service manuals if exist.