Read Panasonic BM-ED500 Service Manual online
2-1
PRINTED CIRCUIT BOARD ASS'Y SETUP PROCEDURE
1. Capture Board, Terminal Board
8
You don't need to setup after replacing the Printed Circuit
Board Ass'y.
Board Ass'y.
2. Power Board
8
Carry out the voltage adjustment according to the
Adjustment Procedure on page 2-4 after replacing the
Power Board Ass'y.
Adjustment Procedure on page 2-4 after replacing the
Power Board Ass'y.
3. G-Box Board
8
Set Dip Switches (SW101, SW102, SW13) on the board
as follows after replacing the G-Box Board Ass'y.
as follows after replacing the G-Box Board Ass'y.
SW101 (Setting Switches 1)
SW102 (Setting Switches 2)
Set same as the Printed Circuit Board Ass'y used before.
SW13 (Operation Mode Switches)
Change the mode to the Recognition Mode or the
Enrollment Mode.
Recognition Mode
Enrollment Mode
4. Control Board
8
It is necessary to set up the Network Setup, transfer the
Initial Setting File and transfer the Iris Database after
replacing the Control Board Ass'y.
Initial Setting File and transfer the Iris Database after
replacing the Control Board Ass'y.
(1) Network Setup
8
Turn off the power of the BM-ED500, and change the Dip
Switch (SW13) on the G-Box Board to the IP Setting
Mode as shown in Fig. 4-1.
Switch (SW13) on the G-Box Board to the IP Setting
Mode as shown in Fig. 4-1.
O F F
1
2
3
4
5
6
7
8
Set according to I/F type.
O F F
1
2
3
4
5
6
7
8
O F F
1
2
3
4
5
6
7
8
Fig. 4-1
8
Turn on the power of the BM-ED500.
8
Wait until the Setup indicator on the G-Box Board
changes from "8" to "0".
changes from "8" to "0".
8
Set the IP Address according to the following procedure
(a)–(h).
(a) Enter the IP Address Setting Command "113
(a)–(h).
(a) Enter the IP Address Setting Command "113
∗
002#"
with the numeric buttons on the G-Box Board.
(b) Enter the IP Address by 12-digit numbers without
period. (Example: When you enter an IP Address
"172.27.1.2", enter "172027001002".)
"172.27.1.2", enter "172027001002".)
(c) Enter the Address Check Command "113
∗
000#" with
the numeric buttons on the G-Box Board, then the
Address will be checked.
After the checking, the result will appear on the Setup
indicator on the G-Box Board.
Address will be checked.
After the checking, the result will appear on the Setup
indicator on the G-Box Board.
Completed: 0
Failed:
Failed:
1 (The Address may be wrong.
Begin again from step (a).)
(d) Turn off the power of the BM-ED500.
(e) Turn on the power of the BM-ED500 again.
(f) Enter the IP Address Confirmation Command
(e) Turn on the power of the BM-ED500 again.
(f) Enter the IP Address Confirmation Command
"112
∗
002#" with the numeric buttons on the G-Box
Board.
(g) Confirm that the each digit of the IP Address is dis-
played on the Setup indicator in a sequential order.
(h) In case of mistake, begin again from step (a).
8
Turn off the power of the BM-ED500.
8
Turn on the power of the BM-ED500 again.
8
Set the Gateway Address according to the following pro-
cedure (a)
cedure (a)
–
(h).
(a) Enter the Gateway Address Setting Command
“113
∗
004#” with the numeric buttons on the G-Box
Board.
(b) Enter the Gateway Address by 12-digit numbers with-
out period. (Example: When you enter an Gateway
Address “172.27.1.254”, enter “172027001254”.)
Address “172.27.1.254”, enter “172027001254”.)
(c) Enter the Address Check Command “113
∗
000#” with
the numeric buttons on the G-Box Board, then the
Address will be checked.
After the checking, the result will appear on the Setup
indicator on the G-Box Board.
Address will be checked.
After the checking, the result will appear on the Setup
indicator on the G-Box Board.
Completed: 0
Failed:
Failed:
1 (The Address may be wrong.
Begin again from step (a).)
(d) Turn off the power of the BM-ED500.
(e) Turn on the power of the BM-ED500 again.
(f)
(e) Turn on the power of the BM-ED500 again.
(f)
Enter the Gateway Address Confirmation Command
“112
“112
∗
004#” with the numeric buttons on the G-Box
Board.
(g) Confirm that the each digit of the Gateway Address is
displayed on the Setup indicator in a sequential
order.
order.
(h) In case of mistake, begin again from step (a).
8
Turn off the power of the BM-ED500.
O F F
1
2
3
4
5
6
7
8
Click on the first or last page to see other BM-ED500 service manuals if exist.