Read JBL ON STAGE 400P (serv.man4) EMC - CB Certificate online
IEC 60950-1 (ed.1)
- Page 4 of 5 -
www.nemko.com
Report No. 100711
TRF No. IECEN60950_1C
The following key national differences are based on requirements other than national regulatory
requirements. The bi-national standard (CAN/CSA C22.2 No. 60950-1/UL 60950-1, First Edition)
should be consulted for further details on the national differences summarized below
requirements. The bi-national standard (CAN/CSA C22.2 No. 60950-1/UL 60950-1, First Edition)
should be consulted for further details on the national differences summarized below
1.5.1
Components of equipment must be suitable for
the application, and must comply with the
requirements of the equipment standard and the
applicable national (Canadian and/or U.S.)
component or material standards, as far as they
may apply.
the application, and must comply with the
requirements of the equipment standard and the
applicable national (Canadian and/or U.S.)
component or material standards, as far as they
may apply.
The acceptance will be based on the following:
I) A component Certified by a Canadian or U.S.
National Certification Body (NCB) to a Canadian
or U.S. component standard will be checked for
correct application and use in accordance with its
specified rating. Where necessary, it will also be
subject to the applicable tests of the equipment
standard.
National Certification Body (NCB) to a Canadian
or U.S. component standard will be checked for
correct application and use in accordance with its
specified rating. Where necessary, it will also be
subject to the applicable tests of the equipment
standard.
J) A component, which has a CB Test Certificate
for compliance with a relevant IEC component
standard, will be checked for correct application
and use in accordance with its specified ratings.
Where necessary, it will also be subject to the
applicable tests of the equipment standard, and
to the applicable tests of the Canadian and/or
U.S. component or material standard, under the
conditions occurring in the equipment.
for compliance with a relevant IEC component
standard, will be checked for correct application
and use in accordance with its specified ratings.
Where necessary, it will also be subject to the
applicable tests of the equipment standard, and
to the applicable tests of the Canadian and/or
U.S. component or material standard, under the
conditions occurring in the equipment.
K) A component, which has no approval as in A)
or B) above or which is used not in accordance
with its specified ratings, will be subject to the
applicable tests of the equipment standard, and
to the applicable tests of the Canadian and/or
U.S. component or material standard, under the
conditions occurring in the equipment.
or B) above or which is used not in accordance
with its specified ratings, will be subject to the
applicable tests of the equipment standard, and
to the applicable tests of the Canadian and/or
U.S. component or material standard, under the
conditions occurring in the equipment.
L) Some components may require annual re-
testing, which may be carried out by the
manufacturer, CSA International or another
laboratory
testing, which may be carried out by the
manufacturer, CSA International or another
laboratory
All critical components are
certified. Refer to appended
table 1.5.1 in main CB Test
Report.
certified. Refer to appended
table 1.5.1 in main CB Test
Report.
P
2.3.1
For TNV-2 and TNV-3 circuits with other than
ringing signals and with voltages exceeding 42.4
Vp or 60 Vdc, the maximum acceptable current
through a 2000 ohm resistor (or greater)
connected across the voltage source with other
loads disconnected is 7.1 mA peak or 30 mA dc
under normal operating conditions.
ringing signals and with voltages exceeding 42.4
Vp or 60 Vdc, the maximum acceptable current
through a 2000 ohm resistor (or greater)
connected across the voltage source with other
loads disconnected is 7.1 mA peak or 30 mA dc
under normal operating conditions.
No TNV circuitry.
N
Click on the first or last page to see other ON STAGE 400P (serv.man4) service manuals if exist.