Read JBL JEMBE WIRELESS (serv.man2) EMC - CB Certificate online
Report No. SF201200115 Page 19 of 32
EN 60065
Clause
Requirement – Test
Result - Remark
Verdict
19.5
Glass surfaces (exc.laminated) with an area
exceeding 0,1 m
exceeding 0,1 m
² or maximum dimension
> 450 mm, pass the test of 19.5.1
N
19.6
Wall or ceiling mountings adequate
N
20
RESISTANCE TO FIRE
P
20.1
Electrical components and mechanical parts
P
a) Exemption for components contained in an
enclosure of material V-0 to IEC 60695-11-10
with openings not exceeding 1 mm in width
enclosure of material V-0 to IEC 60695-11-10
with openings not exceeding 1 mm in width
N
b) Exemption for small components as defined in
20.1
20.1
N
20.1.1
Electrical components meet the requirements of
Clause 14 or 20.1.4
Clause 14 or 20.1.4
N
20.1.2
Insulation of internal wiring working at voltages
> 4 Kv or leaving an internal fire enclosure,
> 4 Kv or leaving an internal fire enclosure,
or
located within the areas mentioned in Table 21,
not contributing to the spread of fire
P
20.1.3
Material of printed circuit boards on which the
available power exceeds 15 W at a voltage
between 50 V and 400 V (peak) a.c. or d.c.
meets V-1 or better to IEC60707, unless used in
a fire enclosure
available power exceeds 15 W at a voltage
between 50 V and 400 V (peak) a.c. or d.c.
meets V-1 or better to IEC60707, unless used in
a fire enclosure
Supply voltage: DC 12V
No potential ignition source.
P
Material of printed circuit boards on which the
available power exceeds 15 W at a voltage
>400 V (peak) a.c. or d.c. meets V-0 to
IEC 60707
available power exceeds 15 W at a voltage
>400 V (peak) a.c. or d.c. meets V-0 to
IEC 60707
N
20.1.4
Components and parts not covered by 20.1.1,
20.1.2 and 20.1.3 (other than fire enclosures)
mounted nearer to a potential ignition source
than the distances in Table 21 comply with the
relevant flammability category in Table 21
20.1.2 and 20.1.3 (other than fire enclosures)
mounted nearer to a potential ignition source
than the distances in Table 21 comply with the
relevant flammability category in Table 21
No potential ignition source
in the equipment.
in the equipment.
N
Components and parts as above but shielded
from a potential ignition source, with the barrier
area in accordance with Table 21 and fig. 13
from a potential ignition source, with the barrier
area in accordance with Table 21 and fig. 13
N
Apparatus with voltages >4kV under normal
operating conditions and distances to the
enclosure exceed those specified Table 21,
flammability classification HB40 or better is
required for the enclosure.
operating conditions and distances to the
enclosure exceed those specified Table 21,
flammability classification HB40 or better is
required for the enclosure.
N
20.2
Fire enclosure
N
20.2.1
Potential ignition sources with open circuit
voltage > 4 kV (peak) a.c. or d.c. contained in a
fire enclosure to V-1
voltage > 4 kV (peak) a.c. or d.c. contained in a
fire enclosure to V-1
N
Click on the first or last page to see other JEMBE WIRELESS (serv.man2) service manuals if exist.