Read Harman Kardon SB 26 (serv.man3) EMC - CB Certificate online
Page 11 of 40
Report No.: ACSCBAV13004
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065K
9
Electric shock hazard under normal operating conditions
For SB26 CNTR: Not directly connected to the mains.
For SB26 SUB: See below
For SB26 CNTR: Not directly connected to the mains.
For SB26 SUB: See below
-
9.1
Testing on the outside
Pass
9.1.1
For voltages >1000 V ac or >1500 V dc complies
with clause 13.3.1 for basic insulation
with clause 13.3.1 for basic insulation
N/A
9.1.1.1
a) Open circuit voltages
Pass
b) Touch current measured from terminal devices
using the network in annex D .................................:
using the network in annex D .................................:
U1: 0.854V peak,
U2: 0.217V peak.
U2: 0.217V peak.
Pass
c) Discharge not exceeding 45 μC
<45 μC. Pass
d) Energy of discharge not exceeding 350 mJ
N/A
9.1.1.2
Test with test finger and test probe
No hazardous live parts are
accessible.
accessible.
Pass
9.1.2
No hazardous live shafts of knobs, handles or levers
Pass
9.1.3
Ventilation holes and other holes tested by means of
4 mm x 100 mm test pin
4 mm x 100 mm test pin
No top ventilation.
N/A
9.1.4
Terminal devices tested with 1 mm x 20 mm test pin
(10 N); test probe D of IEC 61032
(10 N); test probe D of IEC 61032
Pass
Terminal devices tested with 1 mm x 100 mm
straight wire (1 N); test probe D of IEC 61032
straight wire (1 N); test probe D of IEC 61032
Pass
9.1.5
Pre-set controls tested with 2.5 mm x 100 mm test
pin (10 N); test probe C of IEC 61032
pin (10 N); test probe C of IEC 61032
No pre-set controls.
N/A
9.1.6
No shock hazard due to stored charge on withdrawal
of the mains plug; voltage (V) after 2 s ..................:
of the mains plug; voltage (V) after 2 s ..................:
8.3Vdc (Standby)
16.7Vdc (Standby, with R502
opened)
Rating of R502, R503, R504,
R505: 1MΩ
16.7Vdc (Standby, with R502
opened)
Rating of R502, R503, R504,
R505: 1MΩ
Pass
If C is not greater than 0,1 μF no test needed
0.33μF. N/A
9.1.7
Resistance to external forces
Pass
a) Test probe 11 of IEC 61032 for 10 s (50 N)
Pass
b) Test hook of fig. 4 for 10 s (20 N)
Pass
c) 30 mm diameter test tool for 5 s (100 or 250 N)
Conducted on metal enclosure
fixed amplify board.
fixed amplify board.
Pass
9.2
No hazard after removing a cover by hand
N/A
10 Insulation
requirements
For SB26 CNTR: Not directly connected to the mains.
For SB26 SUB: See below
For SB26 SUB: See below
-
10.1
Insulation resistance (MΩ) at least 2 MΩ min. after
surge test for basic and 4 MΩ min. for reinforced
insulation .................................................................:
surge test for basic and 4 MΩ min. for reinforced
insulation .................................................................:
N/A
10.2 Humidity
treatment 48 h or 120 h ...........................: 40
°C, 95%, 120h.
Pass
Click on the first or last page to see other SB 26 (serv.man3) service manuals if exist.