Read Harman Kardon AVR 240 (serv.man13) EMC - CB Certificate online
- Page 7 of 7 -
www.nemko.com
Report No. 65654
14.3.3
Transformer/motor, constructional requirements
P
Transformer Insulation Insulation
Res.
Test Volt
Clearances / Creepage distances
Part No.
Between
M Ohms
kV (60 sec.)
Measured
Required
KLT5W011YE, or
Pr - sec
> 100
3KV (rms)
10,2 / 10,2mm
4,0 / 5,6 mm
CLT5W011YE
Pr - ic
> 100
3KV (rms)
10,2 / 10,2mm
4,0 / 5,0 mm
KLT5J033YE, or
Pr – sec
> 100
3KV (rms)
7,5 / 7,5 mm
4,0 / 5,0 mm
CLT5J033YE
Pr - ic
> 100
3KV (rms)
6,5 / 6,5 mm
4,0 / 5,0 mm
-
Components / construction
(
(
KLT5W011YE or CLT5W011YE)
Windings on two separate bobbins. The
bobbins are placed in an insulating housing with
two compartments, one above the other.
Bobbin thickness: > 0,4mm.
Max. Working voltage: 379Vp/268Vrms
bobbins are placed in an insulating housing with
two compartments, one above the other.
Bobbin thickness: > 0,4mm.
Max. Working voltage: 379Vp/268Vrms
P
Components / construction
(
(
KLT5J033YE o CLT5J033YE)
Windings on single bobbin. The center flange
provided between primary and secondary
windings. Satisfactory constructed.
Bobbin thickness: > 0,4mm.
Max. Working voltage: 344Vp/243Vrms
provided between primary and secondary
windings. Satisfactory constructed.
Bobbin thickness: > 0,4mm.
Max. Working voltage: 344Vp/243Vrms
P
Transformer Insulation
Thick
(mm)
Material
Dielectric strength test
Part No.
Between
X Number
60 sec.
KLT5W011YE, or Pr - sec
0,80 mm min. x 1
PET bobbin
1 layer tested – Pass *)
CLT5W011YE
Pr - ic
0,80 mm min. x 1
PET bobbin
1 layer tested – Pass *)
KLT5J033YE, or
CLT5J033YE
CLT5J033YE
Pr - sec
0,50 mm min. x 2
0,50 mm min. x 1
0,50 mm min. x 1
PET bobbin wall
PBT bobbin cap.
PBT bobbin cap.
1 layer tested – Pass *)
Pr - ic
0,60 mm min. x 1
PET bobbin
1 layer tested – Pass *)
Pr - ic
0,50 mm min. x 1
PBT bobbin cap.
1 layer tested – Pass *)
*) Test voltage: 3000 Vrms
17.1
Torque test to Table 20:
P
Screw
Diameter
With
Without
Material
Torque test (Nm)
Location / function
(mm)
Head
Head
Screw
Nut
Fulfilled / Remarks
Fixing of top cover
(sides)
(sides)
4,0 x -
Metal
Metal
Tested with 1,2Nm,
5 times / Pass
5 times / Pass
Fixing of top cover
(rear)
(rear)
3,0 x -
Metal
Metal
Tested with 0,5Nm,
5 times / Pass
5 times / Pass