KP-51PX3 - Sony TV Service Manual (repair manual). Page 13

To eliminate the amount of remote controls you need, this remote control has a learning feature. Once set up 
as explained below, it can be used in place of your other remote controls.
It is recommended that you make a note of what each button has been taught (you can use the table provided 
with the remote control).

Before you start and for accurate learning, please read below instructions:
• Choose the button (a-g) you want to learn. The buttons which can learn a new function, have a blue dot. See 

fig. 3 to find out the possible buttons.

• Do not move the remote units during the learning procedure.
• Be sure to keep holding down the learning button until your commander reacts as described.
• Use fresh batteries in both remote units.
• Avoid learning in places subjects to direct sunlight or a strong fluorescent light. 
• Noise may interfere during the learning procedure.
• The remote control detector area may differ depending on each remote unit. If learning does not work, try 

changing the positions of the two remote controls.

• It is possible that some specific remote control signals may not be learned.
• If you do not perform the learning steps within 20 seconds at any point during the process, the learning mode 

ends. 

 

 Position both remote controls as shown (see fig. 1). 

 Press and hold the 

t

 button of this TV remote control for 

approximately 6 seconds, until the AUX green light starts flashing 

 (see fig.2).  

 Press the button (a-g, see fig. 3) of this TV remote control on which 
you wish to store a learned function.

Once the selected button has been pressed, the VCR, TV, DVD and 

AUX illuminate flash in order (see fig. 4).

 Press the button from the other remote control that you wish to teach your 

TV remote control.

• During the data transfer process, all the four lights illuminate at the 

same time (see fig. 5).

• As soon as data transfer is finished, the AUX green light starts 

flashing (see fig. 6).

If you wish to record other functions repeat steps 2-4 (read before the 

warning below), otherwise go to step 6.

• In case you try to select one button which has been already 

learned, all the four lights will momentarily flash very shortly and 
the remote control automatically return to the same condition as 
in the step 2 with the AUX light flashing

• In case you try to select a not-learnable button, the remote control 

stay in to the same condition as in the step 2 with the AUX light 
flashing.

Press the 

t

 button to finish the learning process.

Check that all the learning functions have been learned correctly.

• To use a learned function later, press the 

T

 or 

t

 buttons to select AUX and next press 

the relevant button.

• Always remember to press the 

T

 or 

t

 button until the green light iluminates 

according to the equipment you want to operate with this remote control: VCR, TV,  
DVD or AUX. 

 

continued...

2-3 cm.

Other remote 
control

This TV remote 
control

MODE

6 sec.

MODE

MODE

MODE

 Press and hold the 

t

 button for approximately six seconds until the 

AUX green light flashes (see fig. 7). 

 While pressing the 

% button, press the button (a - g) with the learned 

function that you want to erase.  

All the four lights illuminate at the same time (see fig. 8) and as 
soon as the learned function is erased, the AUX green light starts 
flashing (see fig. 9).

 If you wish to store a new function, repeat steps 3 and 4 from the 

previous page, otherwise press the 

t

 button to return to normal 

operation. 

 Press and hold the 

t

 button for approximately six seconds, until the 

AUX green light flashes (see fig. 7). 

 While pressing the 

% button, press 

t

 to erase all the learned 

functions.  

 All the four lights illuminate at the same time (see fig. 8) and 
as soon as all the learned function are erased, the remote 
control automatically returns to the normal operation. 

 

MODE

6 sec.

MODE

MODE