Read Sony DPP-FP97 Service Manual online
3-4
DPP-FP97
3-2-2. COLOR DISPLAY CHECK
The color display can be check using the service mode as follows:
Procedure:
1.
Start the service mode. (Refer to Section 3-1-1.)
2.
Select “LCD Calibrate” using the DIRECTION buttons (f,
F) and press the [ENTER] button.
F) and press the [ENTER] button.
3.
When the DIRECTION buttons (f, F) is pressed, color dis-
play can be confirmed in the following order:
play can be confirmed in the following order:
4.
When the [ENTER] button is pressed, the screen returns to the
service mode startup screen.
service mode startup screen.
Note:
The screen returns to the startup screen of the service
mode when the [CANCEL] button is pressed.
mode when the [CANCEL] button is pressed.
5.
Quit the service mode. (Refer to Section 3-1-1.)
3-2-3. FIRMWARE WRITING AND VERSION
UPGRADE
Note:
Download the latest firmware and obtain the technical memo
from the ESI homepage.
from the ESI homepage.
Writing of firmware:
Be sure to write the latest firmware after replacing the MAI board.
Otherwise, the normal operation cannot be performed.
Be sure to write the latest firmware after replacing the MAI board.
Otherwise, the normal operation cannot be performed.
Version Upgrade:
Perform the version upgrade when the functional upgrade (firm-
ware version upgrade) is required.
Perform the version upgrade when the functional upgrade (firm-
ware version upgrade) is required.
[Procedure of firmware writing and version upgrade]
1.
Download the latest firmware (hereafter referred to as firm-
ware) from the ESI homepage.
ware) from the ESI homepage.
2.
Copy the firmware (downloaded and uncompressed folder) to
the root directory of the memory card (Memory Stick or SD
card).
(s:\SONY\DPPSV\ssssss.bin)
the root directory of the memory card (Memory Stick or SD
card).
(s:\SONY\DPPSV\ssssss.bin)
3.
Insert the memory card into the memory card slot of this unit.
4.
Insert one end of the power cord into the AC adaptor (AC-
S2422) supplied with this unit and insert the other end of the
power cord into the receptacle.
S2422) supplied with this unit and insert the other end of the
power cord into the receptacle.
5.
Insert the DC plug of the supplied AC adaptor into the DC-IN
terminal of this unit.
terminal of this unit.
6.
While pressing the [PRINT] button, press the [ON/STAND-
BY] button.
BY] button.
7.
Release your finger from the button when the ACCESS LED
and the PRINT LED start flashing.
and the PRINT LED start flashing.
8.
Access LED and print LED change into lighting after a few
minutes, and the following display appear in LCD.
minutes, and the following display appear in LCD.
*** SUCCESS ***
Press ENTER to run application
Press ENTER to run application
(Completion of firmware writing or version upgrade)
9.
Press the power button to turn off the power.
10. Remove the memory card.
11. While pressing the [ENTER] and [CANCEL] buttons simulta-
11. While pressing the [ENTER] and [CANCEL] buttons simulta-
neously, press the [ON/STANDBY] button. (Service mode
starts.)
starts.)
12. Release all buttons when the initial screen of the service mode
is displayed on the LCD display.
13. Check that the CHECKSUM value (hexadecimal value) dis-
played on the screen is the same as the value of the firmware
name registered in ESI homepage.
name registered in ESI homepage.
14. Turn off the power and disconnect the power cord from the
receptacle.
Black
White
Gray (thin)
Blue
Green
Red
White
Black
f
F
DPP-FP97 (CED)
CHECKSUM: XXXXXXXX (H)
DATE: DEC 4 2008 15:27:21
USB SERIAL NO: 05000001
H TEMP: 28.7 / R TEMP: 27.9
Print Calibrate
LCD Calibrate
Click on the first or last page to see other DPP-FP97 service manuals if exist.