Read Sony MHS-FS3 / MHS-FS3K (serv.man2) Service Manual online
MHS-FS3/FS3K_ADJ
5-8
5-2-6. Set Language Destination
Language Destination Setting:
Save “lang.txt” in the root directory of the removable disk named “BLOGGIE”.
The content of “lang.txt” is as follows:
Language Destination (for example: 5_UC3) (enter key)
Product ID (10bit) (enter key) (refer to “5-3 PRODUCT ID LIST” (Page 5-9))
S/N (8bit) (enter key)
The following is an example of 5_UC3 Language Destination Setting for MHS-FS3 Black camera.
5_UC3
0002095730
08432345
Especially Attention:
1) The enter key must be the end symbol of each row.
2) For the Product ID, refer to “5-3 PRODUCT ID LIST” (Page 5-9), and the Product ID must be 10bit.
If the Product ID is less than 10 bit, add 0 before the Product ID.
3) The S/N must be 8 bit. It refer to the serial number of shipment.
The adjustment is finished abnormally.
Set LangDest NG!
Pls check Lang.txt
Fig. 5-2-38
or if MassProduct!
Malfunction of Set Language
Destination
In case of the Set Language
Destination is failed, reset the
language destination.
The adjustment finished normally.
Set LangDest OK!
S/N:
0002095730
Fig. 5-2-37
Color: Black
ProductNum:
08432345
Dest: 5_UC3
The adjustment is complete.
Note: The screen shown above is an example.
5-2-5. 360 Adjustment (MHS-FS3K Only)
The 360 Adjustment is as follows.
Press and hold both sides of the 360 video lens (1), then attach it to the
camera in the direction (2).
Note1: Attach the hooks of the 360 video lens to the attaching parts of the
camera, as shown in Fig. 5-2-33.
Note2: When repairing the parts related to the lens module of MHS-FS3K.
• Ask the customer to send the 360 Video Lens with the unit.
• Perform 360 Adjustment with the 360 Video Lens sent from the
customer.
The adjustment finished normally.
Save callb value OK
Fig. 5-2-35
Save status OK
Ct X:xxxx Yxxx offset Xxx Yx
Ct X:xxxx Yxxx offset Xxx Yx
The adjustment is complete.
The adjustment is finished abnormally.
out of the range
Fig. 5-2-36
Malfunction of 360 Adjustment.
If the white pane departs from
the 360 video lens too much,
which cause it is beyond the
compensation scope of FW.
Fig. 5-2-33
Equipments required: 360 video lens
360 video lens
1
2
1
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
Set the camera to the adjustment mode.
∗ For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Press the
button (Key S1), then Language Destination Setting starts.
Press the MOVIE/ENTER button (Key OK).
the adjustment completion indication appears
on the screen in a moment. (Fig. 5-2-37)
The adjustment will proceed to “5-2-7 Check all above
adjustment result” (Page 5-9), do not execute any
key operation.
In case of the adjustment is finished normally,
the following indication appears on the screen.
(Fig. 5-2-38)
and readjust.
In case of the adjustment is finished abnormally,
In this case, confirm the adjusting environment
Set the camera to the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Mount the 360 video lens to the camera. (Fig. 5-2-33)
Press the MOVIE/ENTER button (Key OK).
In case of the adjustment is finished normally, the
adjustment completion indication appears on the screen.
(Fig. 5-2-35)
The adjustments required when replacing Lens Unit for
MHS-FS3K are completed.
Remove the adjustment FW according to procedures
shown below.
1) Turn off the power of the camera.
2) Disconnect the USB extension cable from the USB
charge adaptor.
3) Connect the USB extension cable disconnected in
step 2) to PC.
4) Turn on the power of the camera.
5) Remove the SDV5095C.bin saved in the
“BLOGGIE_SW” root directory.
the following indication appears on the screen.
(Fig. 5-2-36)
In case of the adjustment is finished abnormally,
In this case, confirm the adjusting environment
and readjust.
Press the Multi-selector button “ B (Key Right)”, then press the
button (Key S1).
Move the white pane to match it with the center of the ring-shaped image
by pressing the Multi-selector buttons “v (Key Up)”, “V (Key Down)”,
“b (Key Left)” and “B (Key Right)”.
White pane
Ring-shaped image
Fig. 5-2-34
Adjustment order
Screen display
Adjustment order
Screen display
Click on the first or last page to see other MHS-FS3 / MHS-FS3K (serv.man2) service manuals if exist.