Read Sony MHS-FS3 / MHS-FS3K (serv.man2) Service Manual online
MHS-FS3/FS3K_ADJ
5-7
5-2-4. Bright Pixel Adjustment
The Bright Pixel Adjustment is as follows.
Note:
• Perform this adjustment after that performed in “5-2-2. AWB Adjustment”.
(Page 5-5)
• The Bright Pixel Adjustment proceeds automatically.
• It may take more than 40 minutes to perform the Bright Pixel Adjustment
due to the status of the camera (including more than 1 minutes for warming-
up, and more than 20 minutes for main adjustment).
The adjustment finished normally.
Fig. 5-2-30
OK Burnin defect pixel
The adjustment is complete.
The adjustment is finished abnormally.
Still Adjusting ...
BadCount: xxxxx
Bright Pixel NG XXX
over
Fig. 5-2-31
Malfunction of Bright Pixel
Adjustment
NG Burnin dfect Pixel
Fig. 5-2-32
Malfunction of Burnin dfect
Pixel Adjustment
Fig. 5-2-26
Run: 00XX TimeCnt: 0XXX
Connect the USB charging adaptor.
Fig. 5-2-28
XXXX XX Adj...
Bright Thd: XXXX
Over
XXXX XX Adj...
Bright Thd: XXXX
Below
The automatic adjustment is complete.
Fig. 5-2-29
Run: 00XX TimeCnt: 0360
The warming up is complete.
Fig. 5-2-27
Still Adjusting...
The adjustment starts automatically.
Fig. 5-2-25
Equipments required: Cover camera lens
(All black)
Camera
Black cloth
Check that the camera is on the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
∗ For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Cover camera lens (all black). (Fig. 5-2-25)
Press the Multi-selector button “ V (Key Down)”.
the adjustment completion indication appears
on the screen. (Fig. 5-2-30)
The adjustments required when replacing Lens Unit
for MHS-FS3 are completed.
Remove the adjustment FW according to
procedures shown below.
1) Turn off the power of the camera.
2) Disconnect the USB extension cable from the USB
charge adaptor.
3) Connect the USB extension cable disconnected in
step 2) to PC.
4) Turn on the power of the camera.
5) Remove the SDV5095C.bin saved in the
“BLOGGIE_SW” root directory.
In case of the adjustment is finished normally,
the following indication appears on the screen.
(Fig. 5-2-31 and 5-2-32)
In case of the adjustment is finished abnormally,
In case of the Bright Pixel Adjustment is failed,
after turning off the power of the camera,
restart the adjustment from the “5-2-2 AWB
Adjustment” (Page 5-5).
Press the
button (Key S1), then Bright Pixel Adjustment starts.
Connect the USB charging adaptor after the screen turned to that shown in Fig. 5-2-26.
The camera will automatically keep operating abnormally for more than 1 minutes during warming up.
Perform the adjustment from beginning if the screen got frozen.
The screen will light out for a few seconds, then turn to that shown in Fig. 5-2-27 and start the adjustment automatically.
After the automatic adjustment finished, the screen will turn to that shown in Fig. 5-2-28.
In case of “Over”, warming up will restart automatically.
In case of “Below”, it will proceed to the next step automatically.
The camera will automatically keep operating abnormally for more than 20 minutes
after the screen turned to that shown in Fig. 5-2-29.
Perform the adjustment from beginning if the screen got frozen.
Adjustment order
Screen display
Click on the first or last page to see other MHS-FS3 / MHS-FS3K (serv.man2) service manuals if exist.