Read Sony MHS-FS3 / MHS-FS3K (serv.man2) Service Manual online
MHS-FS3/FS3K_ADJ
5-6
5-2-3. 3D Adjustment
1) To use the FS3-chart, print out 4 pages of FS3-chart in A3 size (by
100%) from the manual, and make them in one page by matching
the number of each fitting mark“
”.
the width : 772mm
the height: 546mm
2) Attach the FS3-chart set above on the wall.
2) Attach the FS3-chart set above on the wall.
Note : • Make sure that the distance is 85 ± 1 cm between the FS3-chart and
the tip of camera lens.
• Set the camera to make it face to the FS3-chart.
• Set the FS3-chart while confirming the LCD to make the green pane
“ ”
at the center of the chart match the center of the LCD.
Color temperature = 4000 to 7000K
Luminance: LV11 to 13
The adjustment finished normally.
Fig. 5-2-21
3D OK OOO
The adjustment is complete.
The adjustment is finished abnormally.
Fail to Get Pos
Fig. 5-2-22
Malfunction of 3D Adjustment
3D NG XXX
Fig. 5-2-23
Malfunction of 3D Adjustment
NG:XY Over Offset
Fig. 5-2-24
Malfunction of 3D Adjustment
Check that the camera is on the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
∗ For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in front of the FS3-chart. (Fig. 5-2-20)
the adjustment completion indication appears
on the screen. (Fig. 5-2-21)
Turn off the power to quit the adjustment mode.
In case of the adjustment is finished normally,
the following indication appears on the screen.
(Fig. 5-2-22 and 5-2-24)
In case of the adjustment is finished abnormally,
In this case, confirm the adjusting environment
and readjust.
Press the
button (Key S1), then 3D Adjustment starts.
Press the
button (Key S1).
Fig. 5-2-20
Equipment required: FS3-chart
FS3-chart
85 1cm
Camera
+-
(2) Lens Shading Adjustment
When the indication (Fig. 5-2-16) appears on the LCD display, set the
adjustment jig according to procedures shown below. (Fig. 5-2-17)
1) Set the Light balance filter to make it cover the surfaces of both
camera lenses.
2) place the camera in front of the small pattern box.
The Lens Shading Adjustment order is as follows.
The adjustment finished normally.
Fig. 5-2-18
Lens shading OK OOO
The adjustment is complete.
The adjustment is finished abnormally.
Lens shading NG XXX
Fig. 5-2-19
Malfunction of Lens Shading
Adjustment
Fig. 5-2-17
Equipment required: Small pattern box (PTB-1450)
Cover camera lens and
Small pattern box (PTB-1450)
(All black)
Light balance filter
Light balance filter
Small pattern box
(PTB-1450)
3mm or less
Black cloth
Camera
Setting of Small pattern box (PTB-1450) with the Light balance
filter:
Color temperature = 5200 ± 300K
Luminance: LV9.4 ± 0.2
Fig. 5-2-16
Lens Shading ADJ...
VX.XXADJ
20XX-XX-XX
Please Key S1 Start...
Attach the Light balance filter to the tip of the camera lens.
Check that the “AWB Adjustment” (Page 5-5) is finished normally.
Place the camera in front of the Small pattern box (PTB-1450) and cover them (all black) with black cloth. (Fig. 5-2-17)
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
the adjustment completion indication appears
on the screen. (Fig. 5-2-18)
Turn off the power to quit the adjustment mode.
In case of the adjustment is finished normally,
the following indication appears on the screen.
(Fig. 5-2-19)
In case of the adjustment is finished abnormally,
In this case, confirm the adjusting environment
and readjust.
Press the
button (Key S1), then Lens Shading Adjustment starts.
Adjustment order
Screen display
Adjustment order
Screen display
Click on the first or last page to see other MHS-FS3 / MHS-FS3K (serv.man2) service manuals if exist.