Read Sony HDR-TD30 / HDR-TD30E / HDR-TD30V / HDR-TD30VE (serv.man2) Service Manual online
HDR-TD30/TD30E/TD30V/TD30VE_L2
1-4
Self-diagnosis Code
Symptom/State
Correction
Repaired by:
Block
Function
Detailed
Code
E
6
1
1
1
The abnormalities in initialization of the focus
lens and the abnormalities in initialization of
the zoom lens occurred simultaneously.
Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.
E
6
1
3
0
Reset position detection error on the stepper
iris initializing
Turn the power on to open lens barrier. Disconnect the battery or power
cord, and then connect again.
Confirm that the iris blades in lens are working.
If iris blades do not working, check the iris motor drive IC in lens
drive block (CN1012 pin wg, wh or CN1014 pin wg, wh on VC-655
board).
If iris blades work normally, confirm that they are closing completely
and confirm following item.
･ Case of the iris blades do not close normally, replace the lens device.
･ Case of “E: 61: 30” is appeared and iris blades closed completely.
･ Case of the iris blades do not close normally, replace the lens device.
･ Case of “E: 61: 30” is appeared and iris blades closed completely.
Confirm that communication with lens device is normal.
･ Case of LCD is not displayed normally, check that connection
･ Case of LCD is not displayed normally, check that connection
between lens device (CM-123 board) and CN1007 or CN1011 on
VC-655 board by FP-1505 flexible board.
･ Case of LCD is displayed normally, replace the lens device.
E
6
2
0
0
Handshake correction function does not work
well. (With PITCH angular velocity sensor
output stopped.)
Inspect PITCH angular velocity sensors (SE7501 on the JK-404 board)
peripheral circuits.
E
6
2
0
1
Handshake correction function does not work
well. (With YAW angular velocity sensor
output stopped.)
Inspect YAW angular velocity sensors (SE7501 on the JK-404 board)
peripheral circuits.
E
6
2
0
2
Abnormality of IC for steadyshot.
Refer to “1-7-1. E : 62 : 02 (Abnormality of IC for Steadyshot) Oc-
curred”.
E
6
2
0
3
IC for steadyshot and micro controller com-
munication abnormality among.
Inspect the steadyshot circuit (IC5501 on the VC-655 board).
E
6
2
0
4
Image vibration correction during
handshake function does not work.
Inspect the image vibration angular velocity sensors (SE7701 on the
VC-655 board) peripheral circuits.
E
6
2
1
0
Shift lens initializing failure.
Replacement of lens device. (Note 3) If an error occurs again, replace
the VC-655 board.
E
6
2
1
1
Shift lens overheating (Pitch)
Refer to “1-7-2. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred”.
E
6
2
1
2
Shift lens overheating (Yaw)
Refer to “1-7-3. E : 62 : 12 [Shift Lens Overheating (Yaw)] Occurred”.
E
6
2
2
0
Abnormality of thermistor.
Refer to “1-7-4. E : 62 : 20 [Abnormality of Thermistor] Occurred”.
E
9
1
0
1
Abnormality when flash is being charged.
Checking of flash unit or replacement of FP-1501 flexible board.
E
9
1
0
2
Abnormality of flash unit.
Checking of flash unit or replacement of FP-1501 flexible board.
E
9
1
0
3
Abnormality of flash unit Temperature
detection.
Checking of flash unit or replacement of FP-1501 flexible board.
E
9
2
0
1
Battery current value goes over the max
discharge current
Check the remaining battery power because this symptom maybe
depended on the remaining battery level, and confirm whether or
not the symptom is occurred after replacing the battery. If the symp-
tom is still occurred, overhaul inspection is needed. Connect the
CN8002 of MM-103 board with CN1001 of VC-655 board.
Check each output of DC/DC converter (IC4301) on VC-655 board
with the AC adaptor connected DC JACK (J001).
(The minimum connection to periphery)
E
9
4
0
0
Fault of writing or erasing the flash memory
Inspect the flash memory (IC8101 on the MM-103 board).
E
9
4
0
1
Internal flash memory fault
Inspect the flash memory (IC8101 on the MM-103 board).
E
9
4
0
2
BGM data error
Check the CPU (IC1301 on the VC-655 board).
E
9
5
0
0
GPS hardware error
TD30V/TD30VE:
Check whether the FFC-277 flexible flat cable is broken, and check
whether it is inserted imperfectly.
If there is no problem the flexible board, inspect or replacement of
the GP-037 board.
E
9
6
0
0
Map area mount error
TD30V/TD30VE:
Inspect or replacement of the MM-103 board.
E
9
7
0
0
Projector hardware error
Turn power off and turn power on again.
Note 2: Functions of codes with * mark are not provided in this unit.
Note 3: When the lens device was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
Note 3: When the lens device was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-7. METHOD OF COPING WITH SHIFT LENS ERROR
VC-655 BOARD (SIDE A)
VC-655 BOARD (SIDE B)
C5525
C5526
C5527
C5528
C5529
R5506
C5530
C5531
C5532
IC5501
Fig. 1
Measurement points on the VC-655 board
about 330 msec
Note: The length of low section will vary a little depending on the conditions.
Fig. 2
Change in output voltage of R5506 on the VC-655 board
1-7-1. E : 62 : 02 [Abnormality of IC for Steadyshot] Occurred
Order
Procedure
1
Turn the power OFF.
2
While measuring with an oscilloscope the output voltage of R5506 in the periphery of IC5501 on the VC-655 board, turn the
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
3
If the output voltage change as shown in Fig. 2, replace the lens device (Note). If it does not change as shown in Fig. 2, inspect
the camera control circuit (IC1601 of VC-655 board) periphery.
the camera control circuit (IC1601 of VC-655 board) periphery.
Note: When the lens device was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
*
Click on the first or last page to see other HDR-TD30 / HDR-TD30E / HDR-TD30V / HDR-TD30VE (serv.man2) service manuals if exist.