HDR-TD30, HDR-TD30E, HDR-TD30V, HDR-TD30VE (serv.man2) - Sony Movie Service Manual (repair manual). Page 6

HDR-TD30/TD30E/TD30V/TD30VE_L2

1-3

When you replace to the repairing board, write down the sensitivity displayed on the angular velocity sensor SE7501 (PITCH/YAW).
Start the Adjust Manual in the Adjust Station and execute the “GYRO sensor sensitivity adj”.

Note: The sensor sensitivity of SE7501 (PITCH/YAW) on JK-404 board is written only repair parts.

When replacing the lens, write down the PITCH/YAW data given on the data sheet of the replacement lens for service.
Start the Adjust Manual in the Adjust Station and execute the “GYRO sensor sensitivity Adj”.

PITCH data

YAW data

L2
L1

P.PP/Y.YY

P.PP/Y

.YY

SE7501

JK-404 BOARD (SIDE A)

YY

PP

G1

G2

PP: PITCH sensor sensitivity
YY: YAW sensor sensitivity

When problems occur while the unit is operating, the self-diagnosis 
function starts working, and displays on the Viewfinder or the LCD 
screen what to do.
This function consists of two display; self-diagnosis display and service 
mode display.Details of the self-diagnosis functions are provided in the 
Instruction manual.

When problems occur while the unit is operating, the counter of the 
Viewfinder or the LCD screen shows a 4-digit display consisting of an 
alphabet and numbers,
which blinks at 3.2 Hz. This 5-character display indicates the “repaired 
by:”, “block” in which the problem occurred, and “detailed code”of the 
problem.

0 0

3 2

C

Repaired by:

Refer to “1-6-3. Self-diagnosis Code Tabl e”.

Indicates the appropriate

step to be taken.

E.g.
13 ....
32 ....Turn on power again.

Block

Detailed Code

Blinks at 3.2 Hz

C : Corrected by customer

E : Corrected by service

engineer

Format the “memory card”.

LCD screen

Self-diagnosis Code

Symptom/State

Correction

Repaired by:

Block

Function

Detailed

Code

C

0

4

0

0

Non-standard battery is used.

Use the InfoLITHIUM battery.

C

0

6

0

0

The battery pack temperature is high.

Change the battery pack or place it in a cool place.

C

1

3

0

1

Memory card is unformatted.
Memory card is broken.

Format the memory card.
Insert a new memory card.

C

1

3

0

2

Access error

Remove the power source. Reconnect it again and operate your cam-
corder again.

C

1

3

0

3

Access error (External media)

Turn power off and turn power on again.

C

1

3

0

4

Drive fault (External media)

Turn power off and turn power on again.

C

E

3

2

6

1

6

0

0

0

Difficult to adjust focus
(Cannot initialize focus)

Retry turn the power on by the power switch. If it does not recover, check 
the focus MR sensor of lens device (pin 1 to 4 of CN1012 or pin 1 to 
4

 of CN1014 on the VC-655 board). If it is OK, check the focus motor 

drive IC (IC5501 or IC5701 on the VC-655 board).

E

2

0

0

0

Flash memory data are rewritten.

Make flash memory data correct value. (Note 1)

E

3

1

0

0

Drive fault

Turn power off and turn power on again.

E

6

1

1

0

Zoom operations fault

(Cannot initialize zoom lens.)

Inspect the lens device zoom reset signal (pin eg of CN1012 or pin eg 

of CN1014 on the VC-655 board) when zooming is performed when the 

zoom lever is operated, and the zoom motor drive circuit (IC5701 on the 

VC-655 board) when zooming is not performed.

Note 1: Start the Adjust Manual in the Adjust Station and refer to the “DESTINATON DATA WRITE”.

(                                           )