Read Sony HDR-TD30 / HDR-TD30E / HDR-TD30V / HDR-TD30VE (serv.man2) Service Manual online
SERVICE MANUAL
HDR-TD30/TD30E/TD30V/TD30VE_L2
SERVICE NOTE (Check the following note before the service.)
Revision History
Published by Sony Techno Create Corporation
Sony Corporation
LEVEL
2
983472231.pdf
Ver. 1.0 2013.01
3D Digital HD Video Camera Recorder
The components identified by mark
0 or dotted line with mark 0 are
critical for safety.
Replace only with part number
specified.
0 or dotted line with mark 0 are
critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque
marque
0 sont critiques pour la
sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
Ne les remplacer que par une
pièce portant le numéro spécifié.
9-834-722-31
US Model
Canadian Model
AEP Model
North European Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Tourist Model
Ver.
Date
History
Contents
S.M. Rev.
issued
1.0
2013.01
Official Release
—
—
2013A08-1
© 2013.01
1-1.
POWER SUPPLY DURING REPAIRS
1-2.
PRECAUTION ON REPLACING THE VC-655 BOARD
1-3.
ADDITION OF DESTINATION DATA FILE
1-4.
PRECAUTION ON REPLACING THE JK-404 BOARD
1-5.
PRECAUTION ON REPLACING THE LENS
1-6.
SELF-DIAGNOSIS FUNCTION
1-7.
METHOD OF COPING WITH SHIFT LENS ERROR
1-8.
GPS RECEIVING CHECK (TD30V/TD30VE)
1-9.
PRECAUTION ON REPLACING THE MM-103 BOARD (TD30V/TD30VE)
1-10. DISCHARGE OF LED FLASH/VIDEO LIGHT
1-11. PRECAUTION ON REPLACING THE CABINET (BOTTOM)
1-12. 3D EFFECT CHECK FLOW
1-11. PRECAUTION ON REPLACING THE CABINET (BOTTOM)
1-12. 3D EFFECT CHECK FLOW
N
Photo: HDR-TD30V
HDR-TD30/TD30E/TD30V/TD30VE
– 2 –
HDR-TD30/TD30E/TD30V/TD30VE_L2
SPECIFICATIONS
System
Signal format: PAL color, CCIR standards
HDTV 1080/50i, 1080/50p specification
Movie recording format:
HD:
HD:
3D: MPEG-4 MVC/H.264 AVCHD format
Ver.2.0
compatible
2D: MPEG-4 AVC/H.264 AVCHD format
Ver.2.0
compatible
STD:
MPEG2-PS
Audio recording system:
Dolby Digital 2ch/5.1ch
Dolby Digital 5.1 Creator
Photo file format:
DCF
DCF
Ver.2.0
Compatible
Exif
Ver.2.3
Compatible
MPF Baseline Compatible
Recording media (Movie/Photo):
“Memory Stick PRO Duo” media
SD card (Class 4 or faster)
Image device:
4.6 mm (1/3.91 type) CMOS sensor
Recording pixels (photo):
Max. 20 400 000 pixels
*1
(6 016 × 3 384)
(16:9)
Gross: Approx. 5 430 000 pixels
Effective (movie, 16:9)
*2
:
3D: Approx. 3 980 000 pixels
2D: Approx. 5 020 000 pixels
Effective (photo, 16:9):
Approx. 5 020 000 pixels
Effective (photo, 4:3):
Approx. 3 760 000 pixels
Lens: G lens
3D: 10 × (Optical), 12 × (Extended Zoom)
2D: 10 × (Optical)
*2
, 17 × (Extended
Zoom)
*3
, 120 × (Digital)
F 1.8 - F 3.4
f=3.2 mm - 32.0 mm (5/32 in. - 1 5/16 in.)
When converted to a 35 mm still camera
Movie
*2
:
3D: 33.4 mm - 400.8 mm
(1 3/8 in. - 15 7/8 in.) (16:9)
2D: 29.8 mm - 298.0 mm
(1 3/16 in. - 11 3/4 in.) (16:9)
Photo:
29.8 mm - 298.0 mm (1 3/16 in. - 11 3/4 in.)
(16:9)
Color temperature: [Auto], [One Push], [Indoor],
[Outdoor]
Minimum illumination:
Color temperature: [Auto], [One Push], [Indoor],
[Outdoor]
Minimum illumination:
6 lx (lux) (in default setting, shutter speed
1/50
second)
3 lx (lux) ([Low Lux] is set to [On], shutter
speed 1/25 second)
*1
The unique pixel array of Sony’s ClearVid
and the image processing system (BIONZ)
allow still image resolution equivalent to
the sizes described.
allow still image resolution equivalent to
the sizes described.
*2
[
SteadyShot] is set to [Standard] or
[Off].
*3
[
SteadyShot] is set to [Active].
Input/Output connectors
A/V Remote Connector: Video and audio output
jack
HDMI OUT jack: HDMI mini connector
USB jack: mini-AB/Type A (Built-in USB)
(output
jack
HDMI OUT jack: HDMI mini connector
USB jack: mini-AB/Type A (Built-in USB)
(output
only)
Headphone jack: Stereo minijack (
φ 3.5 mm)
MIC input jack: Stereo minijack (
φ 3.5 mm)
LCD screen
Picture: 8.8 cm (3.5 type, aspect ratio 16:9)
Total number of pixels: 1 229 760 (2 562 × 480)
Total number of pixels: 1 229 760 (2 562 × 480)
General
Power requirements: DC 6.8 V/7.2 V (battery
pack) DC 8.4 V (AC Adaptor)
USB Charging: DC 5 V 500 mA/1.5 A
Average power consumption:
Average power consumption:
During camera recording using LCD screen
at normal brightness:
HD: 3D: 5.1 W, 2D: 3.5 W
STD:
3.3
W
Operating temperature: 0 °C to 40 °C
(32 °F to 104 °F)
Storage temperature: –20 °C to +60 °C
(–4 °F to +140 °F)
Dimensions (approx.):
71.5 mm × 63.5 mm × 131 mm (2 7/8 in. ×
2 1/2 in. × 5 1/4 in.) (w/h/d) including the
projecting
parts
71.5 mm × 63.5 mm × 131 mm (2 7/8 in.
× 2 1/2 in. × 5 1/4 in.) (w/h/d) including
the projecting parts, and the supplied
rechargeable battery pack attached
Mass (approx.)
HDR-TD30VE:
HDR-TD30VE:
460 g (1 lb) main unit only
510 g (1 lb 1 oz) including the supplied
rechargeable battery pack
HDR-TD30E:
450 g (15 oz) main unit only
500 g (1 lb 1 oz) including the supplied
rechargeable battery pack
AC Adaptor AC-L200C/AC-L200D
Power requirements: AC 100 V - 240 V,
50 Hz/60 Hz
Current consumption: 0.35 A - 0.18 A
Power consumption: 18 W
Output voltage: DC 8.4 V*
Operating temperature: 0 °C to 40 °C
Power consumption: 18 W
Output voltage: DC 8.4 V*
Operating temperature: 0 °C to 40 °C
(32 °F to 104 °F)
Storage temperature: –20 °C to +60 °C
(–4 °F to +140 °F)
Dimensions (approx.): 48 mm × 29 mm ×
81 mm (1 15/16 in. × 1 3/16 in. × 3 1/4 in.)
(w/h/d) excluding the projecting parts
Mass (approx.): 150 g (5.3 oz) excluding the
power cord (mains lead)
* See the label on the AC Adaptor for other
* See the label on the AC Adaptor for other
specifications.
Rechargeable battery pack NP-FV50
Maximum output voltage: DC 8.4 V
Output voltage: DC 6.8 V
Maximum charge voltage: DC 8.4 V
Maximum charge current: 2.1 A
Capacity
Output voltage: DC 6.8 V
Maximum charge voltage: DC 8.4 V
Maximum charge current: 2.1 A
Capacity
Typical: 7.0 Wh (1 030 mAh)
Minimum: 6.6 Wh (980 mAh)
Type:
Li-ion
Design and specifications of your camcorder and
accessories are subject to change without notice.
• Manufactured under license from Dolby
accessories are subject to change without notice.
• Manufactured under license from Dolby
Laboratories.
These specifications are extracted from the instruction manual of
HDR-TD30E/TD30VE.
HDR-TD30E/TD30VE.
These specifications are extracted from the instruction manual of
HDR-TD30/TD30V.
HDR-TD30/TD30V.
SPECIFICATIONS
System
Signal format: NTSC color, EIA standards
HDTV 1080/60i, 1080/60p specification
Movie recording format:
HD:
HD:
3D: MPEG-4 MVC/H.264 AVCHD format
Ver.2.0
compatible
2D: MPEG-4 AVC/H.264 AVCHD format
Ver.2.0
compatible
STD:
MPEG2-PS
Audio recording system:
Dolby Digital 2ch/5.1ch
Dolby Digital 5.1 Creator
Photo file format:
DCF
DCF
Ver.2.0
Compatible
Exif
Ver.2.3
Compatible
MPF Baseline Compatible
Recording media (Movie/Photo):
“Memory Stick PRO Duo” media
SD card (Class 4 or faster)
Image device:
4.6 mm (1/3.91 type) CMOS sensor
Recording pixels (photo):
Max. 20 400 000 pixels
*1
(6 016 × 3 384)
(16:9)
Gross: Approx. 5 430 000 pixels
Effective (movie, 16:9)
*2
:
3D: Approx. 3 980 000 pixels
2D: Approx. 5 020 000 pixels
Effective (photo, 16:9):
Approx. 5 020 000 pixels
Effective (photo, 4:3):
Approx. 3 760 000 pixels
Lens: G lens
3D: 10 × (Optical), 12 × (Extended Zoom)
2D: 10 × (Optical)
*2
, 17 × (Extended
Zoom)
*3
, 120 × (Digital)
F 1.8 - F 3.4
f=3.2 mm - 32.0 mm (5/32 in. - 1 5/16 in.)
When converted to a 35 mm still camera
Movie
*2
:
3D: 33.4 mm - 400.8 mm (1 3/8 in. -
15 7/8 in.) (16:9)
2D: 29.8 mm - 298.0 mm (1 3/16 in. -
11 3/4 in.) (16:9)
Photo:
29.8 mm - 298.0 mm (1 3/16 in. - 11 3/4 in.)
(16:9)
Color temperature: [Auto], [One Push], [Indoor],
[Outdoor]
Minimum illumination:
Color temperature: [Auto], [One Push], [Indoor],
[Outdoor]
Minimum illumination:
6 lx (lux) (in default setting, shutter speed
1/60
second)
3 lx (lux) ([Low Lux] is set to [On], shutter
speed 1/30 second)
*1
The unique pixel array of Sony’s ClearVid
and the image processing system (BIONZ)
allow still image resolution equivalent to
the sizes described.
allow still image resolution equivalent to
the sizes described.
*2
[
SteadyShot] is set to [Standard] or
[Off].
*3
[
SteadyShot] is set to [Active].
Input/Output connectors
A/V Remote Connector: Video and audio output
jack
HDMI OUT jack: HDMI mini connector
USB jack: mini-AB/Type A (Built-in USB)
Headphone jack: Stereo minijack (
jack
HDMI OUT jack: HDMI mini connector
USB jack: mini-AB/Type A (Built-in USB)
Headphone jack: Stereo minijack (
φ 3.5 mm)
MIC input jack: Stereo minijack (
φ 3.5 mm)
LCD screen
Picture: 8.8 cm (3.5 type, aspect ratio 16:9)
Total number of pixels: 1 229 760 (2 562 × 480)
Total number of pixels: 1 229 760 (2 562 × 480)
General
Power requirements: DC 6.8 V/7.2 V (battery
pack) DC 8.4 V (AC Adaptor)
USB Charging: DC 5 V 500 mA/1.5 A
Average power consumption:
Average power consumption:
During camera recording using LCD screen
at normal brightness:
HD: 3D: 5.1 W, 2D: 3.5 W
STD:
3.3
W
Operating temperature: 0 °C to 40 °C
(32 °F to 104 °F)
Storage temperature: –20 °C to +60 °C
(–4 °F to +140 °F)
Dimensions (approx.):
71.5 mm × 63.5 mm × 131 mm (2 7/8 in. ×
2 1/2 in. × 5 1/4 in.) (w/h/d) including the
projecting
parts
71.5 mm × 63.5 mm × 131 mm (2 7/8 in.
× 2 1/2 in. × 5 1/4 in.) (w/h/d) including
the projecting parts, and the supplied
rechargeable battery pack attached
Mass (approx.)
HDR-TD30V:
HDR-TD30V:
460 g (1 lb) main unit only
510 g (1 lb 1 oz) including the supplied
rechargeable battery pack
HDR-TD30:
450 g (15 oz) main unit only
500 g (1 lb 1 oz) including the supplied
rechargeable battery pack
AC Adaptor AC-L200C/AC-L200D
Power requirements: AC 100 V - 240 V,
50 Hz/60 Hz
Current consumption: 0.35 A - 0.18 A
Power consumption: 18 W
Output voltage: DC 8.4 V*
Operating temperature: 0 °C to 40 °C
Power consumption: 18 W
Output voltage: DC 8.4 V*
Operating temperature: 0 °C to 40 °C
(32 °F to 104 °F)
Storage temperature: –20 °C to +60 °C
(–4 °F to +140 °F)
Dimensions (approx.): 48 mm × 29 mm ×
81 mm (1 15/16 in. × 1 3/16 in. × 3 1/4 in.)
(w/h/d) excluding the projecting parts
Mass (approx.): 150 g (5.3 oz) excluding the
power cord (mains lead)
* See the label on the AC Adaptor for other
* See the label on the AC Adaptor for other
specifications.
Rechargeable battery pack NP-FV50
Maximum output voltage: DC 8.4 V
Output voltage: DC 6.8 V
Maximum charge voltage: DC 8.4 V
Maximum charge current: 2.1 A
Capacity
Output voltage: DC 6.8 V
Maximum charge voltage: DC 8.4 V
Maximum charge current: 2.1 A
Capacity
Typical: 7.0 Wh (1 030 mAh)
Minimum: 6.6 Wh (980 mAh)
Type:
Li-ion
Design and specifications of your camcorder and
accessories are subject to change without notice.
• Manufactured under license from Dolby
accessories are subject to change without notice.
• Manufactured under license from Dolby
Laboratories.
– 3 –
HDR-TD30/TD30E/TD30V/TD30VE_L2
Model information table
Model
TD30
TD30E
TD30V
TD30VE
Destination
KR
NE/E/CH/JE
US/CND/E
AEP/E/AUS/HK
COLOR system
NTSC
PAL
NTSC
PAL
Internal recording media
–
–
–
–
LENS
CG001 x 2
CG001 x 2
CG001 x 2
CG001 x 2
Projector
–
–
–
–
GPS
–
–
3
3
EVF
–
–
–
–
Active interface shoe
3
3
3
3
Charging capacitor
(for flash)
(for flash)
–
–
–
–
・ Abbreviation
AUS : Australian model
CH
AUS : Australian model
CH
: Chinese model
CND : Canadian model
HK : Hong Kong model
JE
HK : Hong Kong model
JE
: Tourist model
KR
: Korea model
NE
: North European Model
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0 OR DOTTED LINE WITH
MARK
0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE
0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes and
bridges.
bridges.
2. Check the interboard wiring to ensure that no wires are “pinched”
or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
replacement.
replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
6. Flexible Circuit Board Repairing
• Set the soldering iron tip temperature to 350 °C approximately.
• Do not touch the soldering iron on the same conductor of the circuit
• Do not touch the soldering iron on the same conductor of the circuit
board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
UNLEADED SOLDER
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the
Boards requiring use of unleaded solder are printed with the lead free
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the
lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
• Set the soldering iron tip temperature to 350 °C approximately.
If cannot control temperature, solder/unsolder at high temperature
for a short time.
Caution: The printed pattern (copper foil) may peel away if the
for a short time.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
• Be sure to control soldering iron tips used for unleaded solder and
those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.
leaded solder and leaded solder will cause detachment phenomenon.
HDR-TD30/TD30E/TD30V/TD30VE_L2
1-1
1. SERVICE NOTE
1-1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off
so that the unit cannot operate.
These following method is available to prevent this.
so that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor.
1-2. PRECAUTION ON REPLACING THE VC-655 BOARD
Note the following when replacing the board.
Destination Data
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.
After the board replacement, the error of the built-in recording media may be displayed. In this case, execute the [DESTINATION DATA WRITE]
then the error will be cleared. If it is not cleared with [DESTINATION DATA WRITE], format the built-in recording media.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.
After the board replacement, the error of the built-in recording media may be displayed. In this case, execute the [DESTINATION DATA WRITE]
then the error will be cleared. If it is not cleared with [DESTINATION DATA WRITE], format the built-in recording media.
USB Serial Save
When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform “USB SERIAL SAVE” to get the data.
Start the Adjust Manual in the Adjust Station and perform “USB SERIAL SAVE” to get the data.
USB Serial No. and Product ID
The unit is shipped after an ID (USB Serial No.) unique to each unit and an ID (Product ID) unique to each model have been written.
These IDs have not been written in a new board for service, and therefore they must be entered after the board replacement.
After the board has been replaced with a board for service, start the Adjust Manual in the Adjust Station and execute the “PRODUCT ID & USB
SERIAL No. INPUT” and enter these IDs.
These IDs have not been written in a new board for service, and therefore they must be entered after the board replacement.
After the board has been replaced with a board for service, start the Adjust Manual in the Adjust Station and execute the “PRODUCT ID & USB
SERIAL No. INPUT” and enter these IDs.
Note: A
newly entered Product ID is not always equal to the ID before board replacement. If the new ID differs from the previous ID, it may cause a difference
from the ID registered by the customer.
1-3. ADDITION OF DESTINATION DATA FILE
If the Destination Data file included in the Adjust manual is old, “DESTINATION DATA WRITE” cannot be executed in some cases.
In that case, download a new Destination Data file from the TISS homepage according to the following procedure.
In that case, download a new Destination Data file from the TISS homepage according to the following procedure.
Note 1: To perform Destination Data Write for this model, the Adjust manual of the DSC-WX50 series must have been installed.
Install the Adjust manual of the DSC-WX50 series in advance.
Note 2: The actual image may differ from the image shown above.
1) If the Destination Data file in the Adjust manual in use is old, the window shown in Fig. 1 is displayed.
Click the [OK] button.
Fig.
1
2) The Destination Data Write window opens.
Check the version of the Destination Data file retained in the Adjust manual.
Destination Ver. window