Read Sony HDR-CX630V / HDR-PJ630V / HDR-PJ650E / HDR-PJ650V / HDR-PJ650VE / HDR-PJ660 / HDR-PJ660E / HDR-PJ660V / HDR-PJ660VE (serv.man2) Service Manual online
1-9
HDR-CX630V/PJ630V/PJ650E/PJ650V/PJ650VE/PJ660/PJ660E/PJ660V/PJ660VE_L2
(12) Remove the screw, and remove the boss and the claw to detach the
Front Ornament.
TO
P
FRONT
Boss
Claw
Screw
Front Ornament
(13) Peel off the CM Radiation Sheet.
TO
P
FRONT
CM Radiation Sheet
(14) Peel off the adhesive part of the LF-2026 Flexible Board.
TO
P
FRONT
Adhesive part
LF-2026 Flexible Board
(15) Remove the two screws and disconnect the connector to detach the
Sheet Metal (D-Sub), the LF-2026 Flexible Board.
TOP
FRONT
TO
P
FRONT
Connector
Screw
Screw
Sheet Metal (D-Sub),
LF-2026 Flexible Board
LF-2026 Flexible Board
(16) Peel off the adhesive part of the LF-2026 Flexible Board.
Adhesive part
LF-2026 Flexible Board
Sheet Metal (D-Sub)
– ENGLISH –
(17) Remove the two screws and remove the two bosses to detach the
Sheet Metal (A).
Peel off the Polyimide Sheet.
TO
P
FRON
T
Sheet Metal (A)
Bosses
Polyimide Sheet
Screw
Screw
(18) Disconnect the connector and peel off the adhesive part of the LF-
2027 Flexible Board.
TOP
FRON
T
Adhesive part
Connector
LF-2027 Flexible Board
(19) Remove the two screws and remove the CM-123 Board, Seal Rub-
ber, Optical Filter Block from the Lens Device (LSV-1400B).
TO
P
FRONT
Screw
Screw
Optical Filter Block
Seal Rubber
CM-123 Board
Lens Device (LSV-1400B)
Installation
(1) Install the Optical Filter Block, Seal Rubber, CM-123 Board to the
Lens Device (LSV-1400B), and then tighten two screws in the order
shown in the figure below.
shown in the figure below.
Tightening torque = 0.13 ± 0.01N · m (1.3 ± 0.1kg f · cm)
Note :
2
1
Optical Filter Block
(Note)
(Note)
Optical Filter Block
Refer to
“Assembly-3: How to distinguish the side of
Optical Filter Block facing to Lens Device.
”.
TO
P
FRO
NT
Screw
Screw
Seal Rubber
CM-123 Board
Lens Device (LSV-1400B)
(2) Connect the connector of the LF-2027 Flexible Board and stick the
adhesive part of the Flexible Board.
If the adhesive force is lowered, cut the Adhesive Sheet as shown
in the figure in the frame and then stick it.
in the figure in the frame and then stick it.
TO
P
FRON
T
Adhesive part
Connector
LF-2027 Flexible Board
LF-2027 Flexible Board
Shape and sticking position
of the Adhesive Sheet
of the Adhesive Sheet
Adhesive Sheet
Click on the first or last page to see other HDR-CX630V / HDR-PJ630V / HDR-PJ650E / HDR-PJ650V / HDR-PJ650VE / HDR-PJ660 / HDR-PJ660E / HDR-PJ660V / HDR-PJ660VE (serv.man2) service manuals if exist.