HDR-CX405, HDR-CX440, HDR-PJ410, HDR-PJ440 - Sony Movie Service Manual (repair manual). Page 13

Repaired by:

Block
Function

Detailed
Code

E

6 2

1 0

Shift lens initializing failure

Replacement of lens block. 

*1

If an error occurs again, steadyshot circuit may be faulty.
Replace the board that contains this peripheral circuit.

E

6 2

1 1

Shift lens overheating (PITCH)

Check signal line connections from CPU through steady-
shot IC to PITCH/YAW drive.
When there is no problem with the connections, check
whether this error is due to the lens or the board. Replace
the faulty lens or board.

E

6 2

1 2

Shift lens overheating (YAW)

Check signal line connections from CPU through steady-
shot IC to PITCH/YAW drive.
When there is no problem with the connections, check
whether this error is due to the lens or the board. Replace
the faulty lens or board.

E

6 2

2 0

Abnormality of thermistor

Check signal line connections from CPU through steady-
shot IC to PITCH/YAW drive.
When there is no problem with the connections, check
whether this error is due to the lens or the board. Replace
the faulty lens or board.

E

6 2

3 0

Abnormal CPU

Turn power off and turn power on again. When this error is
not cleared, replace the board that mounts the CPU.

E

9 1

0 1 

*2

Abnormality when flash is being
charged

Check or replace the LED flash/video light or charging ca-
pacitor.

E

9 1

0 2 

*2

Abnormality of LED video light

Check or replace the LED flash/video light or charging ca-
pacitor.

E

9 1

0 3 

*2

Abnormality of LED video light
Temperature detection

Check or replace the LED flash/video light or charging ca-
pacitor.

E

9 2

0 1

Battery current value goes over the
max discharge current

Confirm whether or not the symptom is occurred after re-
placing the battery. If the symptom is still occurred, replace
board.

E

9 4

0 0

Fault of writing or erasing the inter-
nal memory

The internal memory may be faulty.
Replace the board that contains this peripheral circuit.

E

9 4

0 1

Abnormality of the internal memory

The internal memory may be faulty.
Replace the board that contains this peripheral circuit.

E

9 4

0 2

BGM data error

The CPU may be faulty.
Replace the board that contains this peripheral circuit.

E

9 5

0 0 

*2

GPS hardware error

Check the signal line connection for GPS.
When there is no problem with the connections, replace the
board that contains this peripheral circuit.

E

9 5

0 1 

*2

Acceleration sensor hardware error

The acceleration sensor may be faulty.
Replace the board that contains this peripheral circuit.

E

9 5

0 2 

*2

Electronic compass hardware error
(GPS hardware error)

The peripheral circuit of the electronic compass may be
faulty.
Replace the board that contains this peripheral circuit.

E

9 6

0 0 

*2

Map area mount error

The flash memory (Internal Memory) may be faulty.
Replace the board that contains this peripheral circuit.

E

9 7

0 0

Projector hardware error

Turn power off and turn power on again. When this error is
not cleared, the peripheral circuit of the projector may be
faulty.
Replace the board that contains this peripheral circuit.

*1:

When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items. After
the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.

*2:

Function of this code is not provided in this unit.

HDR-CX405/HDR-CX440/HDR-PJ410/HDR-PJ440

1-3