Read Sony DEV-3 / DEV-5 (serv.man2) Service Manual online
DEV-3/5_L2
1-1
1. SERVICE NOTE
1-1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off
so that the unit cannot operate.
These following method is available to prevent this.
so that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor.
1-2. PRECAUTION ON REPLACING THE VC-642 BOARD
Note the following when replacing the board.
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.
After the board replacement, the error of the built-in recording media may be displayed. In this case, execute the [DESTINATION DATA WRITE]
then the error will be cleared. If it is not cleared with [DESTINATION DATA WRITE], format the built-in recording media.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.
After the board replacement, the error of the built-in recording media may be displayed. In this case, execute the [DESTINATION DATA WRITE]
then the error will be cleared. If it is not cleared with [DESTINATION DATA WRITE], format the built-in recording media.
USB SERIAL SAVE
When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform “USB SERIAL SAVE” to get the data.
Start the Adjust Manual in the Adjust Station and perform “USB SERIAL SAVE” to get the data.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.
1-3. PRECAUTION ON REPLACING THE US-019 BOARD
Angular Velocity Sensor
When you replace to the repairing board, write down the sensitivity displayed on the angular velocity sensor SE7501 (PITCH/YAW).
Start the Adjust Manual in the Adjust Station and execute the “GYRO sensor sensitivity adj”.
Start the Adjust Manual in the Adjust Station and execute the “GYRO sensor sensitivity adj”.
Note: The sensor sensitivity of SE7501 (PITCH/YAW) on US-019 board is written only repair parts.
US-019 BOARD (SIDE A)
YY PP
G1
G2
PP:
PITCH sensor sensitivity
PITCH sensor sensitivity
YY:
YAW sensor sensitivity
YAW sensor sensitivity
– ENGLISH –
1-4. PRECAUTION ON REPLACING THE LENS
When replacing the lens, write down the PITCH/YAW data given on the data sheet of the replacement lens for service.
Start the Adjust Manual in the Adjust Station and execute the “GYRO sensor sensitivity Adj”.
Start the Adjust Manual in the Adjust Station and execute the “GYRO sensor sensitivity Adj”.
PITCH/YAW Data
MAIN (Left lens)
SUB (Right lens)
YAW data
P.PP/Y.YY
P.PP/Y.YY
P.PP/Y.YY
PITCH data
1-5. PRECAUTION ON REPLACING THE EVF BLOCK
When replacing the EVF block, write down the PITCH/YAW data given on the data sheet of the replacement EVF block for service.
Start the Adjust Manual in the Adjust Station and execute the “Viewfinder Adj”.
Start the Adjust Manual in the Adjust Station and execute the “Viewfinder Adj”.
PP
YY
YAW data
PITCH data
Click on the first or last page to see other DEV-3 / DEV-5 (serv.man2) service manuals if exist.