Read Sony DCR-VX2000 / DCR-VX2000E (serv.man2) Service Manual online
— 2 —
SELF-DIAGNOSIS FUNCTION
4.
SELF-DIAGNOSIS CODE TABLE
(Refer to page 8)
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
E
Detailed
Code
3
0
4
0
4
2
9
7
9
8
9
9
1
0
1
1
2
0
2
1
2
2
2
3
2
4
3
0
4
0
4
2
9
7
9
8
9
9
0
0
Symptom/State
FG fault when starting capstan.
FG fault when starting drum.
FG fault during normal drum operations.
Mechanical position fault.
Mechanical position fault.
Mechanical position fault.
LOAD direction loading motor time-
out.
out.
UNLOAD direction loading motor
time-out.
time-out.
T reel side tape slacking when
unloading.
unloading.
Winding S reel fault when counting
the rest of tape.
the rest of tape.
T reel fault.
S reel fault.
T reel fault.
FG fault when starting capstan.
FG fault when starting drum
FG fault during normal drum
operations
operations
Mechanical position fault.
Mechanical position fault.
Mechanical position fault.
Difficult to adjust focus
(Cannot initialize focus.)
(Cannot initialize focus.)
Self-diagnosis Code
Repaired b
y
:
Correction
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Inspect the lens block focus reset sensor (Pin wg of LA-026 board)
when focusing is performed when the control dial is rotated in the
focus manual mode, and the focus motor drive circuit (IC140 of
LA-026 board) when the focusing is not performed.
when focusing is performed when the control dial is rotated in the
focus manual mode, and the focus motor drive circuit (IC140 of
LA-026 board) when the focusing is not performed.
: Added portion.
: Changed portion.
Block
Function
3
1
3
1
3
1
3
1
3
1
3
1
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
6
1
Click on the first or last page to see other DCR-VX2000 / DCR-VX2000E (serv.man2) service manuals if exist.